Subversion Repositories svn.mios32

Rev

Rev 2630 | Blame | Compare with Previous | Last modification | View Log | RSS feed

##################################################
# Setup File for midiphy left handed JA Frontpanel
# $Id: MBSEQ_HW.V4 2542 2017-11-04 22:41:11Z tk $
##################################################


##################################################
# Shift Register Setup
##################################################

# maximum number of connected shift registers in a DIN or DOUT chain (1..23)
SRIO_NUM_SR    16

# number of first and second DOUT shift register used for GP LEDs
GP_DOUT_L_SR    0
GP_DOUT_R_SR    0

# DOUTs for Dual Color option:
GP_DOUT_L2_SR  0
GP_DOUT_R2_SR  0

# OPTIONAL: individual track LEDs can optionally be assigned to SRs:
# they correspond with the BUTTON_DIRECT_TRACK* buttons
TRACKS_DOUT_L_SR 0
TRACKS_DOUT_R_SR 0

# sets the debounce delay for low-quality buttons in mS
# use low values for high quality buttons - this ensures best latency.
# use higher values for lower quality buttons.
# Recommended values:
#   - 0   for high quality buttons (we used it many months w/o complaints)
#   - 5  is the default
#   - 20 for low-quality buttons
DEBOUNCE_DELAY 5


##################################################
# Optional BLM Matrix
##################################################

# set this value to 1 if each track has its own set of 16 LEDs to display unmuted steps and current sequencer position
# or if you are using a button/led matrix for misc. button/LED functions
BLM_ENABLED     1

# define the shift registers to which the anodes of these LEDs are connected
# Note: they can be equal to GP_DOUT_[LH]_SR, this saves two shift registers, but doesn't allow a separate view of UI selections
BLM_DOUT_L1_SR  0
BLM_DOUT_R1_SR  0

# define the shift register to which the cathodes of these LEDs are connected
# Note that the whole shift register (8 pins) will be allocated! The 4 select lines are duplicated (4 for LED matrix, 4 for button matrix)
# The second DOUT_CATHODES2 selection is optional if LEDs with high power consumption are used - set this to 0 if not used
BLM_DOUT_CATHODES_SR1  0
BLM_DOUT_CATHODES_SR2  0

# set an inversion mask for the DOUT shift registers if sink drivers (transistors)
# have been added to the cathode lines
# Settings: 0x00 - no sink drivers
#           0xf0 - sink drivers connected to D0..D3
#           0x0f - sink drivers connected to D7..D4
BLM_DOUT_CATHODES_INV_MASK 0x00

# 0: no DUO colour LEDs are connected to the LED matrix (position marker inverts step LED)
# 1: DUO colour LEDs are connected to the LED matrix, second LED displays position marker
# 2: Like option 1, but the first LED is turned off when the position marker activates the second LED
BLM_DOUT_DUOCOLOUR  0

# define the shift registers to which the anodes of the "second colour" (red) LEDs are connected
BLM_DOUT_L2_SR  0
BLM_DOUT_R2_SR  0

# set this to 1 if a button matrix is connected
BLM_BUTTONS_ENABLED 1

# set this to 1 if these buttons should only control the "step triggers" (gate, and other assigned triggers) - and no UI functions
BLM_BUTTONS_NO_UI   1

# optional (only useful in conjunction with the BLM):
# if 0: the GP buttons/LEDs are working as usual
# if 1: the GP buttons/LEDs always select the page items like if the MENU button is pressed,
#       the GP LEDs show the selected page (if matching with any of these items)
BLM_GP_ALWAYS_SELECT_MENU_PAGE 0

# define the DIN shift registers to which the button matrix is connected
BLM_DIN_L_SR  0
BLM_DIN_R_SR  0


##################################################
# Additional 8x8 BLM as used for midiphy Frontpanel
##################################################

# set to 1 to enable 8x8 BLM driver
BLM8X8_ENABLED  1

# first "A" Matrix: left LeMEC
# to which shift register are the select lines connected?
# Allowed values: 0 to disable, 1..16 to assign shift register
BLM8X8_DOUT_CATHODES_SR  3

# set an inversion mask for the DOUT shift registers if sink drivers (transistors)
# have been added to the cathode lines
BLM8X8_DOUT_CATHODES_INV_MASK 0xff

# set an inversion mask for the DOUT shift registers if source drivers (transistors)
# have been added to the anode lines
BLM8X8_DOUT_ANODES_INV_MASK 0xff

# to which shift register are the LED anode lines connected?
# Allowed values: 0 to disable, 1..16 to assign shift register
BLM8X8_DOUT_LED_SR      4

# 0: no mapping of 8x8 LEDs
# 1: select GP LED -> 8x8 matrix mapping for Wilba's MB-SEQ PCB
# 2: select LED mapping for MBSEQ V4L SRIO board
# 3: select GP LED -> matrix mapping for midiphy PCB
BLM8X8_DOUT_GP_MAPPING  3

# 8x8 matrix for misc. button functions
BLM8X8_DIN_SR  3


# second "B" Matrix: right LeMEC 
BLM8X8B_DOUT_CATHODES_SR        8
BLM8X8B_DOUT_CATHODES_INV_MASK  0xff
BLM8X8B_DOUT_ANODES_INV_MASK    0xff
BLM8X8B_DOUT_LED_SR             9
BLM8X8B_DIN_SR                  6

# third "C" Matrix, JA PCB
BLM8X8C_DOUT_CATHODES_SR        1
BLM8X8C_DOUT_CATHODES_INV_MASK  0x00
BLM8X8C_DOUT_ANODES_INV_MASK    0x00
BLM8X8C_DOUT_LED_SR             2
BLM8X8C_DIN_SR                  1


##################################################
# Optional BPM digits
##################################################

# set to 1 or 2 to enable the 3 optional BPM digits
# 0: BPM digits disabled
# 1: BPM digits with common cathode
# 2: BPM digits with common anode
BPM_DIGITS_ENABLED 0

# define the DOUT shift register to which the segments are connected (0=disabled)
BPM_DIGITS_SEGMENTS_SR 0

# define the DOUT SR and pin to which the common pins are connected
# we are counting from right to left
# Example: 140.5 BPM: (COMMON1 = .5, COMMON2=0., COMMON3=4, COMMON4=1)
#                       SR  Pin
BPM_DIGITS_COMMON1_PIN   0   0
BPM_DIGITS_COMMON2_PIN   0   0
BPM_DIGITS_COMMON3_PIN   0   0
BPM_DIGITS_COMMON4_PIN   0   0


##################################################
# Optional Step digits
##################################################

# set to 1 or 2 to enable the 3 optional STEP digits
# 0: STEP digits disabled
# 1: STEP digits with common cathode
# 2: STEP digits with common anode
STEP_DIGITS_ENABLED 0

# define the DOUT shift register to which the segments are connected (0=disabled)
STEP_DIGITS_SEGMENTS_SR 0

# define the DOUT SR and pin to which the common pins are connected
# we are counting from right to left
# Example: Step 123: (COMMON1 = 3, COMMON2=2, COMMON3=1)
#                       SR  Pin
STEP_DIGITS_COMMON1_PIN   0   0
STEP_DIGITS_COMMON2_PIN   0   0
STEP_DIGITS_COMMON3_PIN   0   0


##################################################
# Optional LED Track Position Display 
# See also http://www.midibox.org/dokuwiki/doku.php?id=tpd_pcb
##################################################

# set to 1 or 2 to enable the relative track position display
# 0: TPD disabled
# 1: TPD enabled - columns are cathodes, rows are anodes
# 2: TPD enabled - columns are anodes, rows are cathodes
# 3: TPD for midiphy frontpanel enabled - columns are anodes, rows are cathodes, inversion
TPD_ENABLED 3

# define the DOUT shift register to which the columns are connected (0=disabled)
TPD_COLUMNS_SR_L 5

# for a 16x16 TPD: define the SR to which the right columns are connected (0=disabled, use only 8x8 TPD)
TPD_COLUMNS_SR_R 0

# define the DOUT shift register to which the green LED rows are connected (0=disabled)
TPD_ROWS_SR_GREEN_L 6

# define the DOUT shift register to which the right green LED rows are connected (0=disabled, use only 8x8 TPD)
TPD_ROWS_SR_GREEN_R 7

# define the DOUT shift register to which the red LED rows are connected (0=disabled)
TPD_ROWS_SR_RED_L 0

# define the DOUT shift register to which the right red LED rows are connected (0=disabled, use only 8x8 TPD)
TPD_ROWS_SR_RED_R 0


##################################################
# CV and Gate/Trigger/Sync Setup
##################################################

# AOUT interface now selected in CV Configuration Menu and stored in MBSEQ_GC.V4 file
# please scroll through the menu to find this page!

# the 8 CV gates can be assigned to a shift register (0=off, 1-32: number of shift register):
# - 1st CV Gate available at DOUT SR output D7
# - 2nd CV Gate available at DOUT SR output D6
# - 3rd CV Gate available at DOUT SR output D5
# - ...
# - 8th CV Gate available at DOUT SR output D0
CV_GATE_SR1   0

# and DIN Clock Outputs can be assigned to a shift register as well (0=off, 1-32: number of shift register):
# D7..D0 will output individual clock or start/stop signals which can be configured in the CV configuration page
CLK_SR        0

# additional gate triggers are available on common digital output pins of the
# DOUT shift register chain - they are assigned to AOUT channel #16 (Note C-1, C#1, D-1, ...)
# define the shift registers which should be used here (each provides 8 gates)
# Note that SRs assigned to this function cannot be used as LED outputs (exclusive function)
# Allowed values: 1-32, 0 disables the function, all other values invalid and not allowed
DOUT_GATE_SR1   0
DOUT_GATE_SR2   0
DOUT_GATE_SR3   0
DOUT_GATE_SR4   0
DOUT_GATE_SR5   0
DOUT_GATE_SR6   0
DOUT_GATE_SR7   0
DOUT_GATE_SR8   0

# if set to 1, the additional DOUT "gates" will send 1mS pulses
# useful for analog drums
DOUT_1MS_TRIGGER 0

# should J5A/B/C outputs be enabled (0: no, 1: yes, 2: yes, but in open drain mode)?
#  - the 6 first AOUT gates will be forwarded to J5A/B
#  - the remaining last 2 AOUT gates are available at J5C.A10 and J5C.A11 (LPC17: J28.WS and J28.MCLK)
#  - DIN sync clock will be forwarded to J5C:A0 (LPC17: J28.SDA)
#  - DIN sync start/stop will be forwarded to J5C:A1 (LPC17: J28.SC)
#  - if open drain mode enabled (option 2), external pull-ups have to be connected to J5 pins
#    (advantage: pin levels can be pulled to 5V)
#
# NEVER USE THIS TOGETHER WITH ANALOG POTS - IT WILL CAUSE A SHORT CIRCUIT!
J5_ENABLED 1


##################################################
# LED assignments to DOUT pins
# SR = 0: LED disabled
# SR = 1..23:  directly forwarded to DOUT pin
# SR = M1..M8: forwarded to a 8x8 LED matrix
#
# Please note: due to historical reasons, pin 0-7
# are mirrored!
# Pin 0 = DOUT Pin D7
# Pin 1 = DOUT Pin D6
# Pin 2 = DOUT Pin D5
# ...
# Pin 7 = DOUT Pin D0
##################################################

#           SR  Pin
LED_TRACK1   0   0
LED_TRACK2   0   0
LED_TRACK3   0   0
LED_TRACK4   0   0

#                SR  Pin
LED_PAR_LAYER_A   0   0
LED_PAR_LAYER_B   0   0
LED_PAR_LAYER_C   0   0

#           SR  Pin
LED_BEAT    M5B  1
LED_MEASURE M5B  0

#                    SR  Pin
LED_MIDI_IN_COMBINED  0   0
LED_MIDI_OUT_COMBINED 0   0

#           SR  Pin
LED_EDIT    M8B  0
LED_MUTE    M7C  3
LED_PATTERN M8B  2
LED_SONG    M8B  4
LED_PHRASE  M7C  2

#           SR  Pin
LED_SOLO    M2C  1
LED_FAST    M8A  2
LED_FAST2    0   0
LED_ALL     M8A  4

#           SR  Pin
LED_GROUP1   0   0
LED_GROUP2   0   0
LED_GROUP3   0   0
LED_GROUP4   0   0

#                SR  Pin
LED_TRG_LAYER_A   0   0
LED_TRG_LAYER_B   0   0
LED_TRG_LAYER_C   0   0

#          SR  Pin
LED_PLAY   M5C  0
LED_STOP   M4C  0
LED_PAUSE  M6C  0
LED_REW    M2C  0
LED_FWD    M3C  0
LED_LOOP   M4C  1
LED_FOLLOW  0   0

#              SR  Pin
LED_EXIT       M4B  4
LED_SELECT     M8A  6
LED_MENU       M4B  6
LED_BOOKMARK   M1C  2
LED_SCRUB       0   0
LED_METRONOME  M3C  1
LED_RECORD     M5C  1
LED_JAM_LIVE    0   0
LED_JAM_STEP    0   0
LED_LIVE       M6C  1
LED_UTILITY    M8B  6
LED_COPY       M4A  0
LED_PASTE      M4A  2
LED_CLEAR      M4A  4
LED_UNDO        0   0
LED_MOVE       M4A  6
LED_SCROLL     M8A  0

#                  SR  Pin
LED_STEP_VIEW      M1C  3
LED_PAR_LAYER_SEL  M1C  5
LED_TRG_LAYER_SEL  M7C  5
LED_INS_SEL        M7C  4
LED_TRACK_SEL      M1C  4

#                  SR  Pin
LED_TAP_TEMPO       0   0
LED_TEMPO_PRESET    0   0
LED_EXT_RESTART     0   0

#         SR  Pin
LED_DOWN  M4B  0
LED_UP    M4B  2

#             SR  Pin
LED_MIXER      0   0

#                   SR  Pin
LED_TRACK_MODE       0   0
LED_TRACK_GROOVE     0   0
LED_TRACK_LENGTH     0   0
LED_TRACK_DIRECTION  0   0
LED_TRACK_MORPH      0   0
LED_TRACK_TRANSPOSE  0   0
LED_FX               0   0

#                                SR  Pin
LED_MUTE_ALL_TRACKS               0   0
LED_MUTE_TRACK_LAYERS             0   0
LED_MUTE_ALL_TRACKS_AND_LAYERS    0   0
LED_UNMUTE_ALL_TRACKS             0   0
LED_UNMUTE_TRACK_LAYERS           0   0
LED_UNMUTE_ALL_TRACKS_AND_LAYERS  0   0


##################################################
# Button assignments to DIN pins
# SR = 0: Button disabled
# SR = 1..32:  directly triggered from DIN pin
# SR = M1A..M8A: triggered from the first 8x8 button matrix
# SR = M1B..M8B: triggered from the second 8x8 button matrix
# SR = M1B..M8B: triggered from the third 8x8 button matrix
##################################################

#            SR  Pin
BUTTON_DOWN  M4B  0
BUTTON_UP    M4B  1
BUTTON_LEFT   0   0
BUTTON_RIGHT  0   0

#                SR  Pin
BUTTON_SCRUB      0   0
BUTTON_METRONOME M3C  1
BUTTON_TAP_TEMPO  0   0
BUTTON_JAM_LIVE   0   0
BUTTON_JAM_STEP   0   0

#             SR  Pin
BUTTON_STOP   M4C  0
BUTTON_PAUSE  M6C  0
BUTTON_PLAY   M5C  0
BUTTON_REW    M2C  0
BUTTON_FWD    M3C  0
BUTTON_LOOP   M4C  1
BUTTON_FOLLOW  0   0

#              SR  Pin
BUTTON_MENU    M4B  3
BUTTON_SELECT  M8A  7
BUTTON_EXIT    M4B  2

#              SR  Pin
BUTTON_TRACK1   0   0
BUTTON_TRACK2   0   0
BUTTON_TRACK3   0   0
BUTTON_TRACK4   0   0

#                  SR  Pin
BUTTON_PAR_LAYER_A  0   0
BUTTON_PAR_LAYER_B  0   0
BUTTON_PAR_LAYER_C  0   0

#               SR  Pin
BUTTON_EDIT     M8B  4
BUTTON_MUTE     M7C  1
BUTTON_PATTERN  M8B  5
BUTTON_SONG     M8B  6
BUTTON_PHRASE   M7C  0

#            SR  Pin
BUTTON_SOLO  M2C  1
BUTTON_FAST  M8A  5
BUTTON_FAST2  0   0
BUTTON_ALL   M8A  6

#            SR  Pin
BUTTON_GP1   M2A  0
BUTTON_GP2   M2A  1
BUTTON_GP3   M2A  2
BUTTON_GP4   M2A  3
BUTTON_GP5   M6A  4
BUTTON_GP6   M6A  5
BUTTON_GP7   M6A  6
BUTTON_GP8   M6A  7
BUTTON_GP9   M2B  0
BUTTON_GP10  M2B  1
BUTTON_GP11  M2B  2
BUTTON_GP12  M2B  3
BUTTON_GP13  M6B  4
BUTTON_GP14  M6B  5
BUTTON_GP15  M6B  6
BUTTON_GP16  M6B  7

#              SR  Pin
BUTTON_GROUP1   0   0
BUTTON_GROUP2   0   0
BUTTON_GROUP3   0   0
BUTTON_GROUP4   0   0

# alternative (individual) track selection buttons
# LEDs have to be assigned to TRACKS_DOUT_L_SR and TRACKS_DOUT_R_SR
# For midiphy design: these are the selection buttons, TRACKS_DOUT_* ignored (we use predefined BLM8X8_DOUT_GP_MAPPING 3)
#                     SR  Pin
BUTTON_DIRECT_TRACK1  M3A  0
BUTTON_DIRECT_TRACK2  M3A  1
BUTTON_DIRECT_TRACK3  M3A  2
BUTTON_DIRECT_TRACK4  M3A  3
BUTTON_DIRECT_TRACK5  M7A  4
BUTTON_DIRECT_TRACK6  M7A  5
BUTTON_DIRECT_TRACK7  M7A  6
BUTTON_DIRECT_TRACK8  M7A  7
BUTTON_DIRECT_TRACK9  M3B  0
BUTTON_DIRECT_TRACK10 M3B  1
BUTTON_DIRECT_TRACK11 M3B  2
BUTTON_DIRECT_TRACK12 M3B  3
BUTTON_DIRECT_TRACK13 M7B  4
BUTTON_DIRECT_TRACK14 M7B  5
BUTTON_DIRECT_TRACK15 M7B  6
BUTTON_DIRECT_TRACK16 M7B  7

#                   SR  Pin
BUTTON_TRG_LAYER_A   0   0
BUTTON_TRG_LAYER_B   0   0
BUTTON_TRG_LAYER_C   0   0

#                    SR  Pin
BUTTON_TRACK_SEL     M1C  2
BUTTON_LIVE          M6C  1
BUTTON_RECORD        M5C  1
BUTTON_SAVE_ALL      0    0

#                    SR  Pin
BUTTON_PAR_LAYER_SEL M1C  3
BUTTON_TRG_LAYER_SEL M7C  3
BUTTON_INS_SEL       M7C  2

#               SR  Pin
BUTTON_UTILITY  M8B  7
BUTTON_COPY     M4A  0
BUTTON_PASTE    M4A  1
BUTTON_CLEAR    M4A  2
BUTTON_UNDO      0   0
BUTTON_MOVE     M4A  3
BUTTON_SCROLL   M8A  4
BUTTON_BOOKMARK M1C  0

#                 SR  Pin
BUTTON_STEP_VIEW  M1C  1

#                 SR  Pin
BUTTON_EXT_RESTART 0   0

#                SR  Pin
BUTTON_MIXER      0   0

#                SR  Pin
BUTTON_SAVE       0   0

#                   SR  Pin
BUTTON_PATTERN_RMX   0   0

#                 SR  Pin
BUTTON_FOOTSWITCH  0   0

#                 SR  Pin
BUTTON_ENC_BTN_FWD 0   0

#                      SR  Pin
BUTTON_TRACK_MODE       0   0
BUTTON_TRACK_GROOVE     0   0
BUTTON_TRACK_LENGTH     0   0
BUTTON_TRACK_DIRECTION  0   0
BUTTON_TRACK_MORPH      0   0
BUTTON_TRACK_TRANSPOSE  0   0
BUTTON_FX               0   0
BUTTON_TEMPO_PRESET     0   0


#                                   SR  Pin
BUTTON_MUTE_ALL_TRACKS               0   0
BUTTON_MUTE_TRACK_LAYERS             0   0
BUTTON_MUTE_ALL_TRACKS_AND_LAYERS    0   0
BUTTON_UNMUTE_ALL_TRACKS             0   0
BUTTON_UNMUTE_TRACK_LAYERS           0   0
BUTTON_UNMUTE_ALL_TRACKS_AND_LAYERS  0   0


# alternative (individual) bookmark buttons
# no LEDs available!
#                        SR  Pin
BUTTON_DIRECT_BOOKMARK1   0   0
BUTTON_DIRECT_BOOKMARK2   0   0
BUTTON_DIRECT_BOOKMARK3   0   0
BUTTON_DIRECT_BOOKMARK4   0   0
BUTTON_DIRECT_BOOKMARK5   0   0
BUTTON_DIRECT_BOOKMARK6   0   0
BUTTON_DIRECT_BOOKMARK7   0   0
BUTTON_DIRECT_BOOKMARK8   0   0
BUTTON_DIRECT_BOOKMARK9   0   0
BUTTON_DIRECT_BOOKMARK10  0   0
BUTTON_DIRECT_BOOKMARK11  0   0
BUTTON_DIRECT_BOOKMARK12  0   0
BUTTON_DIRECT_BOOKMARK13  0   0
BUTTON_DIRECT_BOOKMARK14  0   0
BUTTON_DIRECT_BOOKMARK15  0   0
BUTTON_DIRECT_BOOKMARK16  0   0


# Encoder buttons (currently hard-coded to FAST function)

#                    SR  Pin
BUTTON_ENC_DATAWHEEL M8C  2
BUTTON_ENC_BPM        0   0

BUTTON_ENC1          M1A  0
BUTTON_ENC2          M1A  1
BUTTON_ENC3          M1A  2
BUTTON_ENC4          M1A  3
BUTTON_ENC5          M5A  4
BUTTON_ENC6          M5A  5
BUTTON_ENC7          M5A  6
BUTTON_ENC8          M5A  7
BUTTON_ENC9          M1B  0
BUTTON_ENC10         M1B  1
BUTTON_ENC11         M1B  2
BUTTON_ENC12         M1B  3
BUTTON_ENC13         M5B  4
BUTTON_ENC14         M5B  5
BUTTON_ENC15         M5B  6
BUTTON_ENC16         M5B  7


##################################################
# Button behaviour
# 0: active mode as long as button pressed
# 1: pressing button toggles the mode
##################################################

BUTTON_BEH_FAST         1
BUTTON_BEH_FAST2        0
BUTTON_BEH_ALL          1
BUTTON_BEH_SOLO         1
BUTTON_BEH_METRONOME    1
BUTTON_BEH_LOOP         1
BUTTON_BEH_FOLLOW       1
BUTTON_BEH_SCRUB        0
BUTTON_BEH_MENU         0
BUTTON_BEH_MUTE         0
BUTTON_BEH_BOOKMARK     0
BUTTON_BEH_STEP_VIEW    0
BUTTON_BEH_TRG_LAYER    0
BUTTON_BEH_PAR_LAYER    0
BUTTON_BEH_INS_SEL      0
BUTTON_BEH_TRACK_SEL    0
BUTTON_BEH_TEMPO_PRESET 0


##################################################
# Special Behaviour of ALL button
# 0: only parameter layers are modified by ALL function
# 1: trigger and parameter layers are modified by ALL function
##################################################
BUTTON_BEH_ALL_WITH_TRIGGERS 0


##################################################
# Encoder Functions
# SR = 0: encoder disabled
# SR = 1..16: DIN assignment
# Types: NON_DETENTED, DETENTED1, DETENTED2, DETENTED3, DETENTED4, DETENTED5
##################################################

#              SR  Pin  Type
ENC_DATAWHEEL   1   7   DETENTED3

# the speed value for the datawheel which is used when the "FAST" button is activated:
ENC_DATAWHEEL_FAST_SPEED 3

#        SR  Pin  Type
ENC_GP1   2   1   DETENTED3
ENC_GP2   2   3   DETENTED3
ENC_GP3   2   5   DETENTED3
ENC_GP4   2   7   DETENTED3
ENC_GP5   4   1   DETENTED3
ENC_GP6   4   3   DETENTED3
ENC_GP7   4   5   DETENTED3
ENC_GP8   4   7   DETENTED3
ENC_GP9   5   1   DETENTED3
ENC_GP10  5   3   DETENTED3
ENC_GP11  5   5   DETENTED3
ENC_GP12  5   7   DETENTED3
ENC_GP13  7   1   DETENTED3
ENC_GP14  7   3   DETENTED3
ENC_GP15  7   5   DETENTED3
ENC_GP16  7   7   DETENTED3

# the speed value for GP encoders which is used when the "FAST" button is activated:
ENC_GP_FAST_SPEED 3

# Auto FAST mode: if a layer is assigned to velocity or CC, the fast button will be automatically
# enabled - in other cases (e.g. Note or Length), the fast button will be automatically disabled
ENC_AUTO_FAST        1

# optional BPM encoder
#              SR  Pin  Type
ENC_BPM         0   0   DETENTED3

# the speed value for the BPM encoder which is used when the "FAST" function is activated
ENC_BPM_FAST_SPEED 3