Subversion Repositories svn.mios

Rev

Rev 1022 | Blame | Compare with Previous | Last modification | View Log | RSS feed

HEADER 3 MBHP_ETH Module

<H1>MIDIbox Hardware Platform, ETH(ernet) Module</H1>

<P><B>This module is only supported by <A HREF="mbhp_core_stm32.html">MBHP_CORE_STM32</A> and <A HREF="mbhp_core_stm32f4.html">MBHP_CORE_STM32F4</A>!</B></P>
<P><B>For <A HREF="mbhp_core_lpc17.html">MBHP_CORE_LPC17</A> just use the integrated Ethernet Interface.</B></P>

<P><CENTER><IMG SRC="mbhp/mbhp_eth_proto.jpg" width=550></CENTER></P>

<DL>
   <DT><H2> <IMG SRC="images/bullet.gif" ALT=""> Download </H2></DT>
   <DD>
   <DD><TABLE WIDTH="100%" BORDER=0 CELLSPACING=5 CELLPADDING=0>
    <TR>
      <TD COLSPAN=4 CLASS=TABCOLOR1>PCB data, can be viewed, modified and converted with <A HREF="http://www.cadsoft.de/download.htm" TARGET="_blank">Eagle Light</A>. The .pdf based schematic has been created with <A HREF="http://opencircuitdesign.com/xcircuit" TARGET="_blank">xcircuit</A>. There are no special eagle schematics available, since components have been netlisted in the .brd file directly!</TD>
    </TR>
    <TR>
      <TD CLASS=TABCOLOR1><FONT SIZE=2><STRONG>Module</STRONG></FONT></td>
      <TD CLASS=TABCOLOR1><FONT SIZE=2><STRONG>Schematic</STRONG></FONT></td>
      <TD CLASS=TABCOLOR1><FONT SIZE=2><STRONG>Layout Data</STRONG></FONT></td>
      <TD CLASS=TABCOLOR1><FONT SIZE=2><STRONG>Quick-view</STRONG></FONT></TD>
    </TR>
    <TR>
      <TD CLASS=TABCOLOR2><I>MBHP_ETH</I></TD>
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_eth_v2.pdf">mbhp_eth_v2.pdf</A></TD>
      <TD CLASS=TABCOLOR2>not available yet</A></TD>
      <TD CLASS=TABCOLOR2>-</A></TD>
    </TR>
  </TABLE></DD>

  <DD><TABLE WIDTH="100%" BORDER=0 CELLSPACING=5 CELLPADDING=0>
    <TR>
      <TD COLSPAN=4 CLASS=TABCOLOR1><FONT SIZE=3>Additional informations</FONT></TD>
    </TR>
    <TR>
      <TD CLASS=TABCOLOR1><FONT SIZE=2><STRONG>File</STRONG></FONT></td>
      <TD CLASS=TABCOLOR1><FONT SIZE=2><STRONG>Size</STRONG></FONT></td>
      <TD NOWRAP CLASS=TABCOLOR1><FONT SIZE=2><STRONG>Description</STRONG></FONT></TD>
    </TR>
    <TR>
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_eth_orderlist.txt">mbhp_eth_orderlist.txt</A></TD>
      <TD CLASS=TABCOLOR2>1k</TD>
      <TD CLASS=TABCOLOR2><A HREF="http://www.reichelt.de/" TARGET="_blank">Reichelt</A> orderlist</TD>
    </TR>
  </TABLE></DD>
  </DD>

<DL>
   <DT><H2> <IMG SRC="images/bullet.gif" ALT=""> IMPORTANT FOR STM32F1 </H2></DT>
   <DD><P CLASS=CL>The resistor array R30 of the <A HREF="mbhp_core_stm32.html">MBHP_CORE_STM32</A> module shouldn't be connected when the ENC28J60 chip (or SD Card) is used, because pads are configured in Push-Pull mode at 3.3V.<BR>
       Ethernet transfers could work unstable with these Pull-Up resistors!</P>
   </DD>

   <DT><H2> <IMG SRC="images/bullet.gif" ALT=""> IMPORTANT FOR LPC17 </H2></DT>
   <DD><P CLASS=CL>This module isn't relevant, as <A HREF="mbhp_core_lpc17.html">MBHP_CORE_LPC17</A> provides an integrated ethernet interface!
   </DD>

   <DT><H2> <IMG SRC="images/bullet.gif" ALT=""> IMPORTANT FOR STM32F4 </H2></DT>
   <DD><P CLASS=CL>Nothing special for this board, just connect the MBHP_ETH module directly to J16 of the MBHP_CORE_STM32F4 module.
   </DD>

</DL>

FOOTER