Subversion Repositories svn.mios

Rev

Rev 1149 | Show entire file | Regard whitespace | Details | Blame | Last modification | View Log | RSS feed

Rev 1149 Rev 1162
Line 122... Line 122...
122
      <TD><IMG SRC="mbhp/mbhp_aout_1.jpg" WIDTH=280 HEIGHT=213 BORDER=0 ALT=""></TD>
122
      <TD><IMG SRC="mbhp/mbhp_aout_1.jpg" WIDTH=280 HEIGHT=213 BORDER=0 ALT=""></TD>
123
      <TD CLASS=TABCOLOR2>Start with soldering the 3 bridges which save you from creating a 2-layer board. You can use the cutted legs of caps and resistors, before you throw them away after you finished all the modules! :-)</TD>
123
      <TD CLASS=TABCOLOR2>Start with soldering the 3 bridges which save you from creating a 2-layer board. You can use the cutted legs of caps and resistors, before you throw them away after you finished all the modules! :-)</TD>
124
    </TR>
124
    </TR>
125
    <TR>
125
    <TR>
126
      <TD><IMG SRC="mbhp/mbhp_aout_2.jpg" WIDTH=280 HEIGHT=210 BORDER=0 ALT=""></TD>
126
      <TD><IMG SRC="mbhp/mbhp_aout_2.jpg" WIDTH=280 HEIGHT=210 BORDER=0 ALT=""></TD>
127
      <TD CLASS=TABCOLOR2>Mount the MAX6007B shunt at the backside of the PCB. Take care that it doesn't get too hot during soldering!</TD>
127
      <TD CLASS=TABCOLOR2>Mount the MAX6007B shunt at the backside of the PCB. The side with the single leg goes to the single copper square on your PCB. The two legs on the other side of the 6007 connect to the copper trace and the ground plane. Make sure that you heat up the ground plane with a little bit of solder before you put the 6007 in place. The ground plane will absorb an awful lot of heat, and if your 6007 is already there when you are trying to heat it up it will be fried.
-
 
128
</TD>
128
    </TR>
129
    </TR>
129
    <TR>
130
    <TR>
130
      <TD><IMG SRC="mbhp/mbhp_aout_3.jpg" WIDTH=280 HEIGHT=219 BORDER=0 ALT=""></TD>
131
      <TD><IMG SRC="mbhp/mbhp_aout_3.jpg" WIDTH=280 HEIGHT=219 BORDER=0 ALT=""></TD>
131
      <TD CLASS=TABCOLOR2>Mount all the parts except for the ICs and check the power supply voltages (see <A HREF="mbhp/mbhp_aout.pdf">schematic</A>).<BR>Thereafter put the ICs into the socket and measure the voltages again.<BR>Connect the PCB to your MIDIbox - the pinning depends on the application, see above. It's a good idea to start with the <A HREF="midibox_cv_v1.html">MIDIbox CV</A> application in order to test the module before using another application, since the calibration is easier.</TD>
132
      <TD CLASS=TABCOLOR2>Mount all the parts except for the ICs and check the power supply voltages (see <A HREF="mbhp/mbhp_aout.pdf">schematic</A>).<BR>Thereafter put the ICs into the socket and measure the voltages again.<BR>Connect the PCB to your MIDIbox - the pinning depends on the application, see above. It's a good idea to start with the <A HREF="midibox_cv_v1.html">MIDIbox CV</A> application in order to test the module before using another application, since the calibration is easier.</TD>
132
    </TR>
133
    </TR>