Subversion Repositories svn.mios

Rev

Rev 867 | Rev 875 | Go to most recent revision | Show entire file | Regard whitespace | Details | Blame | Last modification | View Log | RSS feed

Rev 867 Rev 869
Line 1... Line 1...
1
$Id: CHANGELOG.txt 867 2009-12-03 21:41:27Z tk $
1
$Id: CHANGELOG.txt 869 2009-12-08 21:52:43Z tk $
2
2
3
MIDIboxSID V2.0
3
MIDIboxSID V2.0
4
~~~~~~~~~~~~~~~
4
~~~~~~~~~~~~~~~
5
5
6
   o created patch structure for Lead engine
6
   o created patch structure for Lead engine
Line 629... Line 629...
629
    E.g., with Begin=0x00, End=0x7f, KEY=on, Par=200 you are able to
629
    E.g., with Begin=0x00, End=0x7f, KEY=on, Par=200 you are able to
630
    define different ENV1 Decay parameters for each note.
630
    define different ENV1 Decay parameters for each note.
631
    There are much more usecases of course (e.g. different LFO values,
631
    There are much more usecases of course (e.g. different LFO values,
632
    different waveforms, Sync/Ring enable/disable in certain keyranges)
632
    different waveforms, Sync/Ring enable/disable in certain keyranges)
633
    - be creative :)
633
    - be creative :)
-
 
634
  o Arpeggiator "Easy Chord" function now active in default Lead/Bassline/Multi
-
 
635
    patch
-
 
636
  o sammichSID: F2 button now jumps to Knob page by default (especially
-
 
637
    nice for bassline patches, for other engines the knob assignments
-
 
638
    are mostly not preconfigured)
-
 
639
  o Multi Engine: Knob parameter #6 and #7 now allow to control CutOff
-
 
640
    frequency of left/right channel SID separately. Note that this isn't
-
 
641
    consistent to Lead/Bassline assignments, but unfortunately there is
-
 
642
    no other possible solution.
-
 
643
  o filter page now allows direct L/R channel selection
-
 
644
  o the full control surface now handles the first press of Osc Select, 
-
 
645
    Env Select, LFO Select and Filter Mode/Channel Select as a 
-
 
646
    "jump to page" function if that page was not displayed, and 
-
 
647
    thereafter, function as a "change selection" function. Thus 
-
 
648
    if you are not on the LFO page, pressing LFO Select jumps to 
-
 
649
    LFO page, and then pressing it again will change the selected LFO.
-
 
650
  o this is the christmas edition, therefore the Matrix LEDs are flickering
-
 
651
    during startup ;-)
-
 
652
634
653
635
654
636
MEMO:
655
MEMO:
637
  - in Bassline mode, CCs could control individual knob parameters for
656
  - in Bassline mode, CCs could control individual knob parameters for
638
    left/right channel by using the "current" assignment, and selecting
657
    left/right channel by using the "current" assignment, and selecting
Line 690... Line 709...
690
    if SHIFT button pressed
709
    if SHIFT button pressed
691
710
692
  - add Display the state of OSC1 arp on a custom LED
711
  - add Display the state of OSC1 arp on a custom LED
693
    (pendant to CS_MENU_BUTTON_Arp button function)
712
    (pendant to CS_MENU_BUTTON_Arp button function)
694
713
695
  - Wilba: I've always wished that the full control surface would handle 
714
  - The WT "key" control feature could alternatively start a (short) sequence
696
    the first press of Osc Select, Env Select, LFO Select and Filter Select 
715
    instead of only selecting a single WT position.
697
    as a "jump to page" function if that page was not displayed, and 
716
    This would allow to embedd multiple WT sounds (e.g. drums) into a patch,
698
    thereafter, function as a "change selection" function. Thus if you 
-
 
699
    are not on the LFO page, pressing LFO Select jumps to LFO page, and 
717
    and to select them with the note number (especially nice for multi patches)
700
    then pressing it again would change the selected LFO.
-
 
-
 
718