Subversion Repositories svn.mios32

Compare Revisions

Ignore whitespace Rev 2597 → Rev 2598

/trunk/apps/sequencers/midibox_seq_v4/hwcfg/midiphy_lh/MBSEQ_HW.V4
New file
0,0 → 1,667
##################################################
# Setup File for Antilog Frontpanel
# $Id: MBSEQ_HW.V4 2542 2017-11-04 22:41:11Z tk $
##################################################
 
 
##################################################
# Shift Register Setup
##################################################
 
# maximum number of connected shift registers in a DIN or DOUT chain (1..23)
SRIO_NUM_SR 16
 
# number of first and second DOUT shift register used for GP LEDs
GP_DOUT_L_SR 0
GP_DOUT_R_SR 0
 
# DOUTs for Dual Color option:
GP_DOUT_L2_SR 0
GP_DOUT_R2_SR 0
 
# OPTIONAL: individual track LEDs can optionally be assigned to SRs:
# they correspond with the BUTTON_DIRECT_TRACK* buttons
TRACKS_DOUT_L_SR 0
TRACKS_DOUT_R_SR 0
 
# sets the debounce delay for low-quality buttons in mS
# use low values for high quality buttons - this ensures best latency.
# use higher values for lower quality buttons.
# Recommended values:
# - 0 for high quality buttons (we used it many months w/o complaints)
# - 5 is the default
# - 20 for low-quality buttons
DEBOUNCE_DELAY 5
 
 
##################################################
# Optional BLM Matrix
##################################################
 
# set this value to 1 if each track has its own set of 16 LEDs to display unmuted steps and current sequencer position
# or if you are using a button/led matrix for misc. button/LED functions
BLM_ENABLED 1
 
# define the shift registers to which the anodes of these LEDs are connected
# Note: they can be equal to GP_DOUT_[LH]_SR, this saves two shift registers, but doesn't allow a separate view of UI selections
BLM_DOUT_L1_SR 0
BLM_DOUT_R1_SR 0
 
# define the shift register to which the cathodes of these LEDs are connected
# Note that the whole shift register (8 pins) will be allocated! The 4 select lines are duplicated (4 for LED matrix, 4 for button matrix)
# The second DOUT_CATHODES2 selection is optional if LEDs with high power consumption are used - set this to 0 if not used
BLM_DOUT_CATHODES_SR1 0
BLM_DOUT_CATHODES_SR2 0
 
# set an inversion mask for the DOUT shift registers if sink drivers (transistors)
# have been added to the cathode lines
# Settings: 0x00 - no sink drivers
# 0xf0 - sink drivers connected to D0..D3
# 0x0f - sink drivers connected to D7..D4
BLM_DOUT_CATHODES_INV_MASK 0x00
 
# 0: no DUO colour LEDs are connected to the LED matrix (position marker inverts step LED)
# 1: DUO colour LEDs are connected to the LED matrix, second LED displays position marker
# 2: Like option 1, but the first LED is turned off when the position marker activates the second LED
BLM_DOUT_DUOCOLOUR 0
 
# define the shift registers to which the anodes of the "second colour" (red) LEDs are connected
BLM_DOUT_L2_SR 0
BLM_DOUT_R2_SR 0
 
# set this to 1 if a button matrix is connected
BLM_BUTTONS_ENABLED 1
 
# set this to 1 if these buttons should only control the "step triggers" (gate, and other assigned triggers) - and no UI functions
BLM_BUTTONS_NO_UI 1
 
# optional (only useful in conjunction with the BLM):
# if 0: the GP buttons/LEDs are working as usual
# if 1: the GP buttons/LEDs always select the page items like if the MENU button is pressed,
# the GP LEDs show the selected page (if matching with any of these items)
BLM_GP_ALWAYS_SELECT_MENU_PAGE 0
 
# define the DIN shift registers to which the button matrix is connected
BLM_DIN_L_SR 0
BLM_DIN_R_SR 0
 
 
##################################################
# Additional 8x8 BLM as used for Antilog Frontpanel
##################################################
 
# set to 1 to enable 8x8 BLM driver
BLM8X8_ENABLED 1
 
# first "A" Matrix: left LeMEC
# to which shift register are the select lines connected?
# Allowed values: 0 to disable, 1..16 to assign shift register
# 1 for RH
BLM8X8_DOUT_CATHODES_SR 3
 
# set an inversion mask for the DOUT shift registers if sink drivers (transistors)
# have been added to the cathode lines
BLM8X8_DOUT_CATHODES_INV_MASK 0xff
 
# set an inversion mask for the DOUT shift registers if source drivers (transistors)
# have been added to the anode lines
BLM8X8_DOUT_ANODES_INV_MASK 0xff
 
# to which shift register are the LED anode lines connected?
# Allowed values: 0 to disable, 1..16 to assign shift register
# 2 for RH
BLM8X8_DOUT_LED_SR 4
 
# 0: no mapping of 8x8 LEDs
# 1: select GP LED -> 8x8 matrix mapping for Wilba's MB-SEQ PCB
# 2: select LED mapping for MBSEQ V4L SRIO board
# 3: select GP LED -> matrix mapping for Antilog PCB
BLM8X8_DOUT_GP_MAPPING 3
 
# 8x8 matrix for misc. button functions
# 2 for RH
BLM8X8_DIN_SR 3
 
 
# second "B" Matrix: right LeMEC
# 6 for RH
BLM8X8B_DOUT_CATHODES_SR 8
BLM8X8B_DOUT_CATHODES_INV_MASK 0xff
BLM8X8B_DOUT_ANODES_INV_MASK 0xff
# 7 for RH
BLM8X8B_DOUT_LED_SR 9
# 5 for RH
BLM8X8B_DIN_SR 6
 
# third "C" Matrix, JA PCB
# 8 for RH
BLM8X8C_DOUT_CATHODES_SR 1
BLM8X8C_DOUT_CATHODES_INV_MASK 0x00
BLM8X8C_DOUT_ANODES_INV_MASK 0x00
#9 for RH
BLM8X8C_DOUT_LED_SR 2
#7 for RH
BLM8X8C_DIN_SR 1
 
 
##################################################
# Optional BPM digits
##################################################
 
# set to 1 or 2 to enable the 3 optional BPM digits
# 0: BPM digits disabled
# 1: BPM digits with common cathode
# 2: BPM digits with common anode
BPM_DIGITS_ENABLED 0
 
# define the DOUT shift register to which the segments are connected (0=disabled)
BPM_DIGITS_SEGMENTS_SR 0
 
# define the DOUT SR and pin to which the common pins are connected
# we are counting from right to left
# Example: 140.5 BPM: (COMMON1 = .5, COMMON2=0., COMMON3=4, COMMON4=1)
# SR Pin
BPM_DIGITS_COMMON1_PIN 0 0
BPM_DIGITS_COMMON2_PIN 0 0
BPM_DIGITS_COMMON3_PIN 0 0
BPM_DIGITS_COMMON4_PIN 0 0
 
 
##################################################
# Optional Step digits
##################################################
 
# set to 1 or 2 to enable the 3 optional STEP digits
# 0: STEP digits disabled
# 1: STEP digits with common cathode
# 2: STEP digits with common anode
STEP_DIGITS_ENABLED 0
 
# define the DOUT shift register to which the segments are connected (0=disabled)
STEP_DIGITS_SEGMENTS_SR 0
 
# define the DOUT SR and pin to which the common pins are connected
# we are counting from right to left
# Example: Step 123: (COMMON1 = 3, COMMON2=2, COMMON3=1)
# SR Pin
STEP_DIGITS_COMMON1_PIN 0 0
STEP_DIGITS_COMMON2_PIN 0 0
STEP_DIGITS_COMMON3_PIN 0 0
 
 
##################################################
# Optional LED Track Position Display
# See also http://www.midibox.org/dokuwiki/doku.php?id=tpd_pcb
##################################################
 
# set to 1 or 2 to enable the relative track position display
# 0: TPD disabled
# 1: TPD enabled - columns are cathodes, rows are anodes
# 2: TPD enabled - columns are anodes, rows are cathodes
# 3: TPD for midiphy frontpanel enabled - columns are anodes, rows are cathodes, inversion
TPD_ENABLED 3
 
# define the DOUT shift register to which the columns are connected (0=disabled)
TPD_COLUMNS_SR_L 5
 
# for a 16x16 TPD: define the SR to which the right columns are connected (0=disabled, use only 8x8 TPD)
TPD_COLUMNS_SR_R 0
 
# define the DOUT shift register to which the green LED rows are connected (0=disabled)
TPD_ROWS_SR_GREEN_L 6
 
# define the DOUT shift register to which the right green LED rows are connected (0=disabled, use only 8x8 TPD)
TPD_ROWS_SR_GREEN_R 7
 
# define the DOUT shift register to which the red LED rows are connected (0=disabled)
TPD_ROWS_SR_RED_L 0
 
# define the DOUT shift register to which the right red LED rows are connected (0=disabled, use only 8x8 TPD)
TPD_ROWS_SR_RED_R 0
 
 
##################################################
# CV and Gate/Trigger/Sync Setup
##################################################
 
# AOUT interface now selected in CV Configuration Menu and stored in MBSEQ_GC.V4 file
# please scroll through the menu to find this page!
 
# the 8 CV gates can be assigned to a shift register (0=off, 1-32: number of shift register):
# - 1st CV Gate available at DOUT SR output D7
# - 2nd CV Gate available at DOUT SR output D6
# - 3rd CV Gate available at DOUT SR output D5
# - ...
# - 8th CV Gate available at DOUT SR output D0
CV_GATE_SR1 0
 
# and DIN Clock Outputs can be assigned to a shift register as well (0=off, 1-32: number of shift register):
# D7..D0 will output individual clock or start/stop signals which can be configured in the CV configuration page
CLK_SR 0
 
# additional gate triggers are available on common digital output pins of the
# DOUT shift register chain - they are assigned to AOUT channel #16 (Note C-1, C#1, D-1, ...)
# define the shift registers which should be used here (each provides 8 gates)
# Note that SRs assigned to this function cannot be used as LED outputs (exclusive function)
# Allowed values: 1-32, 0 disables the function, all other values invalid and not allowed
DOUT_GATE_SR1 0
DOUT_GATE_SR2 0
DOUT_GATE_SR3 0
DOUT_GATE_SR4 0
DOUT_GATE_SR5 0
DOUT_GATE_SR6 0
DOUT_GATE_SR7 0
DOUT_GATE_SR8 0
 
# if set to 1, the additional DOUT "gates" will send 1mS pulses
# useful for analog drums
DOUT_1MS_TRIGGER 0
 
# should J5A/B/C outputs be enabled (0: no, 1: yes, 2: yes, but in open drain mode)?
# - the 6 first AOUT gates will be forwarded to J5A/B
# - the remaining last 2 AOUT gates are available at J5C.A10 and J5C.A11 (LPC17: J28.WS and J28.MCLK)
# - DIN sync clock will be forwarded to J5C:A0 (LPC17: J28.SDA)
# - DIN sync start/stop will be forwarded to J5C:A1 (LPC17: J28.SC)
# - if open drain mode enabled (option 2), external pull-ups have to be connected to J5 pins
# (advantage: pin levels can be pulled to 5V)
#
# NEVER USE THIS TOGETHER WITH ANALOG POTS - IT WILL CAUSE A SHORT CIRCUIT!
J5_ENABLED 1
 
 
##################################################
# LED assignments to DOUT pins
# SR = 0: LED disabled
# SR = 1..23: directly forwarded to DOUT pin
# SR = M1..M8: forwarded to a 8x8 LED matrix
#
# Please note: due to historical reasons, pin 0-7
# are mirrored!
# Pin 0 = DOUT Pin D7
# Pin 1 = DOUT Pin D6
# Pin 2 = DOUT Pin D5
# ...
# Pin 7 = DOUT Pin D0
##################################################
 
# SR Pin
LED_TRACK1 0 0
LED_TRACK2 0 0
LED_TRACK3 0 0
LED_TRACK4 0 0
 
# SR Pin
LED_PAR_LAYER_A 0 0
LED_PAR_LAYER_B 0 0
LED_PAR_LAYER_C 0 0
 
# SR Pin
LED_BEAT M5B 1
LED_MEASURE M5B 0
 
# SR Pin
LED_MIDI_IN_COMBINED 0 0
LED_MIDI_OUT_COMBINED 0 0
 
# SR Pin
LED_EDIT M8B 0
LED_MUTE M7C 3
LED_PATTERN M8B 3
LED_SONG M8B 5
LED_PHRASE M7C 2
 
# SR Pin
##LED_SOLO M2C 1
##LED_FAST M8A 3
LED_FAST2 0 0
##LED_ALL M8A 5
 
# SR Pin
LED_GROUP1 0 0
LED_GROUP2 0 0
LED_GROUP3 0 0
LED_GROUP4 0 0
 
# SR Pin
LED_TRG_LAYER_A 0 0
LED_TRG_LAYER_B 0 0
LED_TRG_LAYER_C 0 0
 
# SR Pin
LED_PLAY M5C 0
LED_STOP M4C 0
LED_PAUSE M6C 0
LED_REW M2C 0
LED_FWD M3C 0
LED_LOOP M4C 1
LED_FOLLOW 0 0
 
# SR Pin
LED_EXIT M4B 5
LED_SELECT M8A 7
LED_MENU M4B 7
LED_BOOKMARK M1C 2
LED_SCRUB 0 0
LED_METRONOME M3C 1
LED_RECORD M5C 1
LED_JAM_LIVE 0 0
LED_JAM_STEP 0 0
LED_LIVE M6C 1
LED_UTILITY M8B 7
LED_COPY M4A 0
LED_PASTE M4A 3
LED_CLEAR M4A 5
LED_UNDO 0 0
LED_MOVE M4A 7
LED_SCROLL M8A 0
 
# SR Pin
LED_STEP_VIEW M1C 3
LED_PAR_LAYER_SEL M1C 5
LED_TRG_LAYER_SEL M7C 5
LED_INS_SEL M7C 4
LED_TRACK_SEL M1C 4
 
# SR Pin
LED_TAP_TEMPO 0 0
LED_TEMPO_PRESET 0 0
LED_EXT_RESTART 0 0
 
# SR Pin
LED_DOWN M4B 0
LED_UP M4B 3
 
# SR Pin
LED_MIXER 0 0
 
# SR Pin
LED_TRACK_MODE 0 0
LED_TRACK_GROOVE 0 0
LED_TRACK_LENGTH 0 0
LED_TRACK_DIRECTION 0 0
LED_TRACK_MORPH 0 0
LED_TRACK_TRANSPOSE 0 0
LED_FX 0 0
 
# SR Pin
LED_MUTE_ALL_TRACKS 0 0
LED_MUTE_TRACK_LAYERS 0 0
LED_MUTE_ALL_TRACKS_AND_LAYERS 0 0
LED_UNMUTE_ALL_TRACKS 0 0
LED_UNMUTE_TRACK_LAYERS 0 0
LED_UNMUTE_ALL_TRACKS_AND_LAYERS 0 0
 
 
##################################################
# Button assignments to DIN pins
# SR = 0: Button disabled
# SR = 1..32: directly triggered from DIN pin
# SR = M1A..M8A: triggered from the first 8x8 button matrix
# SR = M1B..M8B: triggered from the second 8x8 button matrix
# SR = M1B..M8B: triggered from the third 8x8 button matrix
##################################################
 
# SR Pin
BUTTON_DOWN M4B 0
BUTTON_UP M4B 1
BUTTON_LEFT 0 0
BUTTON_RIGHT 0 0
 
# SR Pin
BUTTON_SCRUB 0 0
BUTTON_METRONOME M3C 1
BUTTON_TAP_TEMPO 0 0
BUTTON_JAM_LIVE 0 0
BUTTON_JAM_STEP 0 0
 
# SR Pin
BUTTON_STOP M4C 0
BUTTON_PAUSE M6C 0
BUTTON_PLAY M5C 0
BUTTON_REW M2C 0
BUTTON_FWD M3C 0
BUTTON_LOOP M4C 1
BUTTON_FOLLOW 0 0
 
# SR Pin
BUTTON_MENU M4B 3
BUTTON_SELECT M8A 7
BUTTON_EXIT M4B 2
 
# SR Pin
BUTTON_TRACK1 0 0
BUTTON_TRACK2 0 0
BUTTON_TRACK3 0 0
BUTTON_TRACK4 0 0
 
# SR Pin
BUTTON_PAR_LAYER_A 0 0
BUTTON_PAR_LAYER_B 0 0
BUTTON_PAR_LAYER_C 0 0
 
# SR Pin
BUTTON_EDIT M8B 4
BUTTON_MUTE M7C 1
BUTTON_PATTERN M8B 5
BUTTON_SONG M8B 6
BUTTON_PHRASE M7C 0
 
# SR Pin
BUTTON_SOLO M2C 1
BUTTON_FAST M8A 5
BUTTON_FAST2 0 0
BUTTON_ALL M8A 6
 
# SR Pin
BUTTON_GP1 M2A 0
BUTTON_GP2 M2A 1
BUTTON_GP3 M2A 2
BUTTON_GP4 M2A 3
BUTTON_GP5 M6A 4
BUTTON_GP6 M6A 5
BUTTON_GP7 M6A 6
BUTTON_GP8 M6A 7
BUTTON_GP9 M2B 0
BUTTON_GP10 M2B 1
BUTTON_GP11 M2B 2
BUTTON_GP12 M2B 3
BUTTON_GP13 M6B 4
BUTTON_GP14 M6B 5
BUTTON_GP15 M6B 6
BUTTON_GP16 M6B 7
 
# SR Pin
BUTTON_GROUP1 0 0
BUTTON_GROUP2 0 0
BUTTON_GROUP3 0 0
BUTTON_GROUP4 0 0
 
# alternative (individual) track selection buttons
# LEDs have to be assigned to TRACKS_DOUT_L_SR and TRACKS_DOUT_R_SR
# For Antilog design: these are the selection buttons, TRACKS_DOUT_* ignored (we use predefined BLM8X8_DOUT_GP_MAPPING 3)
# SR Pin
BUTTON_DIRECT_TRACK1 M3A 0
BUTTON_DIRECT_TRACK2 M3A 1
BUTTON_DIRECT_TRACK3 M3A 2
BUTTON_DIRECT_TRACK4 M3A 3
BUTTON_DIRECT_TRACK5 M7A 4
BUTTON_DIRECT_TRACK6 M7A 5
BUTTON_DIRECT_TRACK7 M7A 6
BUTTON_DIRECT_TRACK8 M7A 7
BUTTON_DIRECT_TRACK9 M3B 0
BUTTON_DIRECT_TRACK10 M3B 1
BUTTON_DIRECT_TRACK11 M3B 2
BUTTON_DIRECT_TRACK12 M3B 3
BUTTON_DIRECT_TRACK13 M7B 4
BUTTON_DIRECT_TRACK14 M7B 5
BUTTON_DIRECT_TRACK15 M7B 6
BUTTON_DIRECT_TRACK16 M7B 7
 
# SR Pin
BUTTON_TRG_LAYER_A 0 0
BUTTON_TRG_LAYER_B 0 0
BUTTON_TRG_LAYER_C 0 0
 
# SR Pin
BUTTON_TRACK_SEL M1C 2
BUTTON_LIVE M6C 1
BUTTON_RECORD M5C 1
BUTTON_SAVE_ALL 0 0
 
# SR Pin
BUTTON_PAR_LAYER_SEL M1C 3
BUTTON_TRG_LAYER_SEL M7C 3
BUTTON_INS_SEL M7C 2
 
# SR Pin
BUTTON_UTILITY M8B 7
BUTTON_COPY M4A 0
BUTTON_PASTE M4A 1
BUTTON_CLEAR M4A 2
BUTTON_UNDO 0 0
BUTTON_MOVE M4A 3
BUTTON_SCROLL M8A 4
BUTTON_BOOKMARK M1C 0
 
# SR Pin
BUTTON_STEP_VIEW M1C 1
 
# SR Pin
BUTTON_EXT_RESTART 0 0
 
# SR Pin
BUTTON_MIXER 0 0
 
# SR Pin
BUTTON_SAVE 0 0
 
# SR Pin
BUTTON_PATTERN_RMX 0 0
 
# SR Pin
BUTTON_FOOTSWITCH 0 0
 
# SR Pin
BUTTON_ENC_BTN_FWD 0 0
 
# SR Pin
BUTTON_TRACK_MODE 0 0
BUTTON_TRACK_GROOVE 0 0
BUTTON_TRACK_LENGTH 0 0
BUTTON_TRACK_DIRECTION 0 0
BUTTON_TRACK_MORPH 0 0
BUTTON_TRACK_TRANSPOSE 0 0
BUTTON_FX 0 0
BUTTON_TEMPO_PRESET 0 0
 
 
# SR Pin
BUTTON_MUTE_ALL_TRACKS 0 0
BUTTON_MUTE_TRACK_LAYERS 0 0
BUTTON_MUTE_ALL_TRACKS_AND_LAYERS 0 0
BUTTON_UNMUTE_ALL_TRACKS 0 0
BUTTON_UNMUTE_TRACK_LAYERS 0 0
BUTTON_UNMUTE_ALL_TRACKS_AND_LAYERS 0 0
 
 
# alternative (individual) bookmark buttons
# no LEDs available!
# SR Pin
BUTTON_DIRECT_BOOKMARK1 0 0
BUTTON_DIRECT_BOOKMARK2 0 0
BUTTON_DIRECT_BOOKMARK3 0 0
BUTTON_DIRECT_BOOKMARK4 0 0
BUTTON_DIRECT_BOOKMARK5 0 0
BUTTON_DIRECT_BOOKMARK6 0 0
BUTTON_DIRECT_BOOKMARK7 0 0
BUTTON_DIRECT_BOOKMARK8 0 0
BUTTON_DIRECT_BOOKMARK9 0 0
BUTTON_DIRECT_BOOKMARK10 0 0
BUTTON_DIRECT_BOOKMARK11 0 0
BUTTON_DIRECT_BOOKMARK12 0 0
BUTTON_DIRECT_BOOKMARK13 0 0
BUTTON_DIRECT_BOOKMARK14 0 0
BUTTON_DIRECT_BOOKMARK15 0 0
BUTTON_DIRECT_BOOKMARK16 0 0
 
 
 
##################################################
# Button behaviour
# 0: active mode as long as button pressed
# 1: pressing button toggles the mode
##################################################
 
BUTTON_BEH_FAST 1
BUTTON_BEH_FAST2 0
BUTTON_BEH_ALL 1
BUTTON_BEH_SOLO 1
BUTTON_BEH_METRONOME 1
BUTTON_BEH_LOOP 1
BUTTON_BEH_FOLLOW 1
BUTTON_BEH_SCRUB 0
BUTTON_BEH_MENU 0
BUTTON_BEH_MUTE 0
BUTTON_BEH_BOOKMARK 0
BUTTON_BEH_STEP_VIEW 0
BUTTON_BEH_TRG_LAYER 0
BUTTON_BEH_PAR_LAYER 0
BUTTON_BEH_INS_SEL 0
BUTTON_BEH_TRACK_SEL 0
BUTTON_BEH_TEMPO_PRESET 0
 
 
##################################################
# Special Behaviour of ALL button
# 0: only parameter layers are modified by ALL function
# 1: trigger and parameter layers are modified by ALL function
##################################################
BUTTON_BEH_ALL_WITH_TRIGGERS 0
 
 
##################################################
# Encoder Functions
# SR = 0: encoder disabled
# SR = 1..16: DIN assignment
# Types: NON_DETENTED, DETENTED1, DETENTED2, DETENTED3, DETENTED4, DETENTED5
##################################################
 
# SR Pin Type
# 7 for RH
ENC_DATAWHEEL 1 7 DETENTED3
 
# the speed value for the datawheel which is used when the "FAST" button is activated:
ENC_DATAWHEEL_FAST_SPEED 3
 
# all SR -1 for RH
# SR Pin Type
ENC_GP1 2 1 DETENTED3
ENC_GP2 2 3 DETENTED3
ENC_GP3 2 5 DETENTED3
ENC_GP4 2 7 DETENTED3
ENC_GP5 4 1 DETENTED3
ENC_GP6 4 3 DETENTED3
ENC_GP7 4 5 DETENTED3
ENC_GP8 4 7 DETENTED3
ENC_GP9 5 1 DETENTED3
ENC_GP10 5 3 DETENTED3
ENC_GP11 5 5 DETENTED3
ENC_GP12 5 7 DETENTED3
ENC_GP13 7 1 DETENTED3
ENC_GP14 7 3 DETENTED3
ENC_GP15 7 5 DETENTED3
ENC_GP16 7 7 DETENTED3
 
# the speed value for GP encoders which is used when the "FAST" button is activated:
ENC_GP_FAST_SPEED 3
 
# Auto FAST mode: if a layer is assigned to velocity or CC, the fast button will be automatically
# enabled - in other cases (e.g. Note or Length), the fast button will be automatically disabled
ENC_AUTO_FAST 1
 
# optional BPM encoder
# SR Pin Type
ENC_BPM 0 0 DETENTED3
 
# the speed value for the BPM encoder which is used when the "FAST" function is activated
ENC_BPM_FAST_SPEED 3s