Subversion Repositories svn.mios32

Rev

Rev 2530 | Details | Compare with Previous | Last modification | View Log | RSS feed

Rev Author Line No. Line
2530 tk 1
##################################################
2
# Setup File for Antilog Frontpanel
3
# $Id: MBSEQ_HW.V4 2531 2017-10-11 22:55:38Z tk $
4
##################################################
5
 
6
 
7
##################################################
8
# MIDI Remote Keyboard Function
9
##################################################
10
 
11
# The note number which activates the remote function
12
# 96 = C-6 (some MIDI monitors display C-5)
13
# 0 disables the remote keyboard function
14
MIDI_REMOTE_KEY 96
15
 
16
# The CC number which activates the remote function
17
# (e.g. to control it with a footswitch)
18
# Allowed numbers: 1-127 for CC#1..CC#127
19
# 0 disables the function (default)
20
MIDI_REMOTE_CC 0
21
 
22
 
23
##################################################
24
# Track Selection CC
25
# Allows to synchronize track selections with a DAW
26
##################################################
27
 
28
# select the mode:
29
# 0: no CC sent on track changes
30
# 1: send a single CC which contains the track number as value
31
# 2: send CC..CC+15 depending on track number with value 127
32
TRACK_CC_MODE 0
33
 
34
# over which port should the CC be sent?
35
# specifiy: USB1..USB4, OUT1..OUT4, IIC1..IIC4, AOUT (haha ;-), OSC1..OSC4
36
TRACK_CC_PORT USB1
37
 
38
# over which MIDI channel should the CC be sent (1..16)?
39
TRACK_CC_CHANNEL 1
40
 
41
# which CC number should be sent (if TRACK_CC_MODE == 2: the first CC)
42
TRACK_CC_NUMBER 100
43
 
44
 
45
##################################################
46
# Running status optimisation
47
# Enabled by default, should be disabled if a MIDI
48
# device connected to a MIDI port doesn't fully
49
# comply to the MIDI specification.
50
# Expects two parameters: port number and 0/1 to
51
# disable/enable the optimisation.
52
##################################################
53
 
54
# OUT1 (MIDI1 port of MBHP_CORE_STM32 and MBHP_CORE_LPC17 module)
55
RS_OPTIMISATION OUT1 1
56
 
57
# OUT2 (MIDI2 port of MBHP_CORE_STM32 and MBHP_CORE_LPC17 module)
58
RS_OPTIMISATION OUT2 1
59
 
60
# OUT3 (MIDI3 port of MBHP_CORE_STM32 and MBHP_CORE_LPC17 module)
61
RS_OPTIMISATION OUT3 1
62
 
63
# OUT4 (MIDI4 port of MBHP_CORE_LPC17 module)
64
RS_OPTIMISATION OUT4 1
65
 
66
 
67
##################################################
68
# Menu Shortcuts allow a quick selection of menu pages.
69
# Will be displayed when the "MENU" button is pressed
70
# Syntax: MENU_SHORTCUT <gp-button-number> <page-name>
71
#
72
# <gp-button-number> in the range of 1..16
73
# <page-name>: one of these names:
74
#
75
#   - MENU         (Page Menu)
76
#   - FXSEL        (Fx Selection)
77
#   - STEPSEL      (Step Selection)
78
#   - TRGSEL       (Trigger Selection)
79
#   - PARSEL       (Param. Selection)
80
#   - TRACKSEL     (Track Selection)
81
#   - BPM_PRESETS  (BPM Presets)
82
#   - EDIT         (Edit)
83
#   - MUTE         (Mute Tracks)
84
#   - MUTE_PORTS   (Mute Ports)
85
#   - PATTERNS     (Patterns)
86
#   - SONG         (Song)
87
#   - MIXER        (Mixer)
88
#   - EVENTS       (Track Events)
89
#   - MODE         (Track Mode)
90
#   - DIRECTION    (Track Direction)
91
#   - DIVIDER      (Track ClockDivider)
92
#   - LENGTH       (Track Length)
93
#   - TRANSPOSE    (Track Transpose)
94
#   - GROOVE       (Track Groove)
95
#   - TRG_ASSIGN   (Track Triggers)
96
#   - MORPH        (Track Morphing)
97
#   - RANDOM       (Random Generator)
98
#   - EUCLID       (Track Euclid Generator)
99
#   - RECORD       (Record)
100
#   - MANUAL       (Manual Trigger)
101
#   - FX_ECHO      (Track Fx: Echo)
102
#   - FX_HUMANIZER (Track Fx: Humanize)
103
#   - FX_LIMIT     (Track Fx: Limit)
104
#   - FX_LFO       (Track Fx: LFO)
105
#   - FX_DUPLICATE (Track Fx: Duplicate)
106
#   - FX_LOOP      (Global Fx: Loop)
107
#   - FX_SCALE     (Global Fx: Scale)
108
#   - UTIL         (Utilities)
109
#   - BPM          (BPM Selection)
110
#   - OPTIONS      (Options)
111
#   - SAVE         (Save Pattern)
112
#   - METRONOME    (Metronome)
113
#   - MIDI         (MIDI Configuration)
114
#   - MIDIMON      (MIDI Monitor)
115
#   - SYSEX        (SysEx)
116
#   - CVCFG        (CV Configuration)
117
#   - DISK         (Disk (SD Card))
118
#   - ETH_OSC      (Ethernet & OSC)
119
#   - LIVE         (Live Play)
120
#   - REMIX        (Pattern Remix)
121
#   - BOOKMARKS    (Bookmarks)
122
#   - ABOUT        (About this MIDIbox)
123
#
124
##################################################
125
 
126
MENU_SHORTCUT  1 MIXER
127
MENU_SHORTCUT  2 EVENTS
128
MENU_SHORTCUT  3 MODE
129
MENU_SHORTCUT  4 DIRECTION
130
MENU_SHORTCUT  5 DIVIDER
131
MENU_SHORTCUT  6 LENGTH
132
MENU_SHORTCUT  7 TRANSPOSE
133
MENU_SHORTCUT  8 GROOVE
134
MENU_SHORTCUT  9 TRG_ASSIGN
135
MENU_SHORTCUT 10 FXSEL
136
MENU_SHORTCUT 11 MANUAL
137
MENU_SHORTCUT 12 MORPH
138
MENU_SHORTCUT 13 BPM
139
MENU_SHORTCUT 14 SAVE
140
MENU_SHORTCUT 15 MIDI
141
MENU_SHORTCUT 16 SYSEX
142
 
143
 
144
##################################################
145
# Shift Register Setup
146
##################################################
147
 
148
# maximum number of connected shift registers in a DIN or DOUT chain (1..23)
149
SRIO_NUM_SR    16
150
 
151
# number of first and second DOUT shift register used for GP LEDs
152
GP_DOUT_L_SR    0
153
GP_DOUT_R_SR    0
154
 
155
# DOUTs for Dual Color option:
156
GP_DOUT_L2_SR  0
157
GP_DOUT_R2_SR  0
158
 
159
# OPTIONAL: individual track LEDs can optionally be assigned to SRs:
160
# they correspond with the BUTTON_DIRECT_TRACK* buttons
161
TRACKS_DOUT_L_SR 0
162
TRACKS_DOUT_R_SR 0
163
 
164
# sets the debounce delay for low-quality buttons in mS
165
# use low values for high quality buttons - this ensures best latency.
166
# use higher values for lower quality buttons.
167
# Recommended values:
168
#   - 0   for high quality buttons (we used it many months w/o complaints)
169
#   - 5  is the default
170
#   - 20 for low-quality buttons
171
DEBOUNCE_DELAY 5
172
 
173
 
174
##################################################
175
# Optional BLM Matrix
176
##################################################
177
 
178
# set this value to 1 if each track has its own set of 16 LEDs to display unmuted steps and current sequencer position
179
# or if you are using a button/led matrix for misc. button/LED functions
180
BLM_ENABLED     1
181
 
182
# define the shift registers to which the anodes of these LEDs are connected
183
# Note: they can be equal to GP_DOUT_[LH]_SR, this saves two shift registers, but doesn't allow a separate view of UI selections
184
BLM_DOUT_L1_SR	0
185
BLM_DOUT_R1_SR	0
186
 
187
# define the shift register to which the cathodes of these LEDs are connected
188
# Note that the whole shift register (8 pins) will be allocated! The 4 select lines are duplicated (4 for LED matrix, 4 for button matrix)
189
# The second DOUT_CATHODES2 selection is optional if LEDs with high power consumption are used - set this to 0 if not used
190
BLM_DOUT_CATHODES_SR1  0
191
BLM_DOUT_CATHODES_SR2  0
192
 
193
# set an inversion mask for the DOUT shift registers if sink drivers (transistors)
194
# have been added to the cathode lines
195
# Settings: 0x00 - no sink drivers
196
#           0xf0 - sink drivers connected to D0..D3
197
#           0x0f - sink drivers connected to D7..D4
198
BLM_DOUT_CATHODES_INV_MASK 0x00
199
 
200
# 0: no DUO colour LEDs are connected to the LED matrix (position marker inverts step LED)
201
# 1: DUO colour LEDs are connected to the LED matrix, second LED displays position marker
202
# 2: Like option 1, but the first LED is turned off when the position marker activates the second LED
203
BLM_DOUT_DUOCOLOUR  0
204
 
205
# define the shift registers to which the anodes of the "second colour" (red) LEDs are connected
206
BLM_DOUT_L2_SR  0
207
BLM_DOUT_R2_SR  0
208
 
209
# set this to 1 if a button matrix is connected
210
BLM_BUTTONS_ENABLED 1
211
 
212
# set this to 1 if these buttons should only control the "step triggers" (gate, and other assigned triggers) - and no UI functions
213
BLM_BUTTONS_NO_UI   1
214
 
215
# optional (only useful in conjunction with the BLM):
216
# if 0: the GP buttons/LEDs are working as usual
217
# if 1: the GP buttons/LEDs always select the page items like if the MENU button is pressed,
218
#       the GP LEDs show the selected page (if matching with any of these items)
219
BLM_GP_ALWAYS_SELECT_MENU_PAGE 0
220
 
221
# define the DIN shift registers to which the button matrix is connected
222
BLM_DIN_L_SR  0
223
BLM_DIN_R_SR  0
224
 
225
 
226
##################################################
227
# Additional 8x8 BLM as used for Antilog Frontpanel
228
##################################################
229
 
230
# set to 1 to enable 8x8 BLM driver
231
BLM8X8_ENABLED  1
232
 
233
# to which shift register are the select lines connected?
234
# Allowed values: 0 to disable, 1..16 to assign shift register
235
BLM8X8_DOUT_CATHODES_SR  1
236
 
237
# set an inversion mask for the DOUT shift registers if sink drivers (transistors)
238
# have been added to the cathode lines
239
BLM8X8_DOUT_CATHODES_INV_MASK 0xff
240
 
241
# set an inversion mask for the DOUT shift registers if source drivers (transistors)
242
# have been added to the anode lines
243
BLM8X8_DOUT_ANODES_INV_MASK 0xff
244
 
245
# to which shift register are the LED anode lines connected?
246
# Allowed values: 0 to disable, 1..16 to assign shift register
247
BLM8X8_DOUT_LED_SR      2
248
 
249
# 0: no mapping of 8x8 LEDs
2531 tk 250
# 1: select GP LED -> 8x8 matrix mapping for Wilba's MB-SEQ PCB
251
# 2: select LED mapping for MBSEQ V4L SRIO board
252
# 3: select GP LED -> matrix mapping for Antilog PCB
253
BLM8X8_DOUT_GP_MAPPING  3
2530 tk 254
 
255
# 8x8 matrix for misc. button functions
256
BLM8X8_DIN_SR  2
257
 
258
 
259
##################################################
260
# Optional BPM digits
261
##################################################
262
 
263
# set to 1 or 2 to enable the 3 optional BPM digits
264
# 0: BPM digits disabled
265
# 1: BPM digits with common cathode
266
# 2: BPM digits with common anode
267
BPM_DIGITS_ENABLED 0
268
 
269
# define the DOUT shift register to which the segments are connected (0=disabled)
270
BPM_DIGITS_SEGMENTS_SR 0
271
 
272
# define the DOUT SR and pin to which the common pins are connected
273
# we are counting from right to left
274
# Example: 140.5 BPM: (COMMON1 = .5, COMMON2=0., COMMON3=4, COMMON4=1)
275
#                       SR  Pin
276
BPM_DIGITS_COMMON1_PIN   0   0
277
BPM_DIGITS_COMMON2_PIN   0   0
278
BPM_DIGITS_COMMON3_PIN   0   0
279
BPM_DIGITS_COMMON4_PIN   0   0
280
 
281
 
282
##################################################
283
# Optional Step digits
284
##################################################
285
 
286
# set to 1 or 2 to enable the 3 optional STEP digits
287
# 0: STEP digits disabled
288
# 1: STEP digits with common cathode
289
# 2: STEP digits with common anode
290
STEP_DIGITS_ENABLED 0
291
 
292
# define the DOUT shift register to which the segments are connected (0=disabled)
293
STEP_DIGITS_SEGMENTS_SR 0
294
 
295
# define the DOUT SR and pin to which the common pins are connected
296
# we are counting from right to left
297
# Example: Step 123: (COMMON1 = 3, COMMON2=2, COMMON3=1)
298
#                       SR  Pin
299
STEP_DIGITS_COMMON1_PIN   0   0
300
STEP_DIGITS_COMMON2_PIN   0   0
301
STEP_DIGITS_COMMON3_PIN   0   0
302
 
303
 
304
##################################################
305
# Optional LED Track Position Display
306
# See also http://www.midibox.org/dokuwiki/doku.php?id=tpd_pcb
307
##################################################
308
 
309
# set to 1 or 2 to enable the relative track position display
310
# 0: TPD disabled
311
# 1: TPD enabled - columns are cathodes, rows are anodes
312
# 2: TPD enabled - columns are anodes, rows are cathodes
313
TPD_ENABLED 0
314
 
315
# define the DOUT shift register to which the columns are connected (0=disabled)
316
TPD_COLUMNS_SR_L 0
317
 
318
# for a 16x16 TPD: define the SR to which the right columns are connected (0=disabled, use only 8x8 TPD)
319
TPD_COLUMNS_SR_R 0
320
 
321
# define the DOUT shift register to which the green LED rows are connected (0=disabled)
322
TPD_ROWS_SR_GREEN_L 0
323
 
324
# define the DOUT shift register to which the right green LED rows are connected (0=disabled, use only 8x8 TPD)
325
TPD_ROWS_SR_GREEN_R 0
326
 
327
# define the DOUT shift register to which the red LED rows are connected (0=disabled)
328
TPD_ROWS_SR_RED_L 0
329
 
330
# define the DOUT shift register to which the right red LED rows are connected (0=disabled, use only 8x8 TPD)
331
TPD_ROWS_SR_RED_R 0
332
 
333
 
334
##################################################
335
# CV and Gate/Trigger/Sync Setup
336
##################################################
337
 
338
# AOUT interface now selected in CV Configuration Menu and stored in MBSEQ_GC.V4 file
339
# please scroll through the menu to find this page!
340
 
341
# the 8 CV gates can be assigned to a shift register (0=off, 1-32: number of shift register):
342
# - 1st CV Gate available at DOUT SR output D7
343
# - 2nd CV Gate available at DOUT SR output D6
344
# - 3rd CV Gate available at DOUT SR output D5
345
# - ...
346
# - 8th CV Gate available at DOUT SR output D0
347
CV_GATE_SR1   0
348
 
349
# and DIN Clock Outputs can be assigned to a shift register as well (0=off, 1-32: number of shift register):
350
# D7..D0 will output individual clock or start/stop signals which can be configured in the CV configuration page
351
CLK_SR        0
352
 
353
# additional gate triggers are available on common digital output pins of the
354
# DOUT shift register chain - they are assigned to AOUT channel #16 (Note C-1, C#1, D-1, ...)
355
# define the shift registers which should be used here (each provides 8 gates)
356
# Note that SRs assigned to this function cannot be used as LED outputs (exclusive function)
357
# Allowed values: 1-32, 0 disables the function, all other values invalid and not allowed
358
DOUT_GATE_SR1   0
359
DOUT_GATE_SR2   0
360
DOUT_GATE_SR3   0
361
DOUT_GATE_SR4   0
362
DOUT_GATE_SR5   0
363
DOUT_GATE_SR6   0
364
DOUT_GATE_SR7   0
365
DOUT_GATE_SR8   0
366
 
367
# if set to 1, the additional DOUT "gates" will send 1mS pulses
368
# useful for analog drums
369
DOUT_1MS_TRIGGER 0
370
 
371
# should J5A/B/C outputs be enabled (0: no, 1: yes, 2: yes, but in open drain mode)?
372
#  - the 6 first AOUT gates will be forwarded to J5A/B
373
#  - the remaining last 2 AOUT gates are available at J5C.A10 and J5C.A11 (LPC17: J28.WS and J28.MCLK)
374
#  - DIN sync clock will be forwarded to J5C:A0 (LPC17: J28.SDA)
375
#  - DIN sync start/stop will be forwarded to J5C:A1 (LPC17: J28.SC)
376
#  - if open drain mode enabled (option 2), external pull-ups have to be connected to J5 pins
377
#    (advantage: pin levels can be pulled to 5V)
378
#
379
# NEVER USE THIS TOGETHER WITH ANALOG POTS - IT WILL CAUSE A SHORT CIRCUIT!
380
J5_ENABLED 1
381
 
382
 
383
##################################################
384
# LED assignments to DOUT pins
385
# SR = 0: LED disabled
386
# SR = 1..23:  directly forwarded to DOUT pin
387
# SR = M1..M8: forwarded to a 8x8 LED matrix
388
#
389
# Please note: due to historical reasons, pin 0-7
390
# are mirrored!
391
# Pin 0 = DOUT Pin D7
392
# Pin 1 = DOUT Pin D6
393
# Pin 2 = DOUT Pin D5
394
# ...
395
# Pin 7 = DOUT Pin D0
396
##################################################
397
 
398
#           SR  Pin
399
LED_TRACK1   0   0
400
LED_TRACK2   0   0
401
LED_TRACK3   0   0
402
LED_TRACK4   0   0
403
 
404
#                SR  Pin
405
LED_PAR_LAYER_A   0   0
406
LED_PAR_LAYER_B   0   0
407
LED_PAR_LAYER_C   0   0
408
 
409
#           SR  Pin
410
LED_BEAT     0   0
411
LED_MEASURE  0   0
412
 
413
#                    SR  Pin
414
LED_MIDI_IN_COMBINED  0   0
415
LED_MIDI_OUT_COMBINED 0   0
416
 
417
#           SR  Pin
418
LED_EDIT     0   0
419
LED_MUTE     0   0
420
LED_PATTERN  0   0
421
LED_SONG     0   0
422
 
423
#           SR  Pin
424
LED_SOLO     0   0
425
LED_FAST     0   0
426
LED_FAST2    0   0
427
LED_ALL      0   0
428
 
429
#           SR  Pin
430
LED_GROUP1   0   0
431
LED_GROUP2   0   0
432
LED_GROUP3   0   0
433
LED_GROUP4   0   0
434
 
435
#                SR  Pin
436
LED_TRG_LAYER_A   0   0
437
LED_TRG_LAYER_B   0   0
438
LED_TRG_LAYER_C   0   0
439
 
440
#          SR  Pin
441
LED_PLAY    0   0
442
LED_STOP    0   0
443
LED_PAUSE   0   0
444
LED_REW     0   0
445
LED_FWD     0   0
446
LED_LOOP    0   0
447
LED_FOLLOW  0   0
448
 
449
#              SR  Pin
450
LED_EXIT        0   0
451
LED_SELECT      0   0
452
LED_MENU        0   0
453
LED_BOOKMARK    0   0
454
LED_SCRUB       0   0
455
LED_METRONOME   0   0
456
LED_RECORD      0   0
457
LED_JAM_LIVE    0   0
458
LED_JAM_STEP    0   0
459
LED_LIVE        0   0
460
LED_UTILITY     0   0
461
LED_COPY        0   0
462
LED_PASTE       0   0
463
LED_CLEAR       0   0
464
LED_UNDO        0   0
465
LED_MOVE        0   0
466
LED_SCROLL      0   0
467
 
468
#                  SR  Pin
469
LED_STEP_VIEW       0   0
470
LED_PAR_LAYER_SEL   0   0
471
LED_TRG_LAYER_SEL   0   0
472
LED_TRACK_SEL       0   0
473
 
474
#                  SR  Pin
475
LED_TAP_TEMPO       0   0
476
LED_TEMPO_PRESET    0   0
477
LED_EXT_RESTART     0   0
478
 
479
#         SR  Pin
480
LED_DOWN   0   0
481
LED_UP     0   0
482
 
483
#             SR  Pin
484
LED_MIXER      0   0
485
 
486
#                   SR  Pin
487
LED_TRACK_MODE       0   0
488
LED_TRACK_GROOVE     0   0
489
LED_TRACK_LENGTH     0   0
490
LED_TRACK_DIRECTION  0   0
491
LED_TRACK_MORPH      0   0
492
LED_TRACK_TRANSPOSE  0   0
493
LED_FX               0   0
494
 
495
#                                SR  Pin
496
LED_MUTE_ALL_TRACKS               0   0
497
LED_MUTE_TRACK_LAYERS             0   0
498
LED_MUTE_ALL_TRACKS_AND_LAYERS    0   0
499
LED_UNMUTE_ALL_TRACKS             0   0
500
LED_UNMUTE_TRACK_LAYERS           0   0
501
LED_UNMUTE_ALL_TRACKS_AND_LAYERS  0   0
502
 
503
 
504
##################################################
505
# Button assignments to DIN pins
506
# SR = 0: Button disabled
507
# SR = 1..23:  directly triggered from DIN pin
508
# SR = M1..M8: triggered from a 8x8 button matrix
509
##################################################
510
 
511
#            SR  Pin
512
BUTTON_DOWN  M4   2
513
BUTTON_UP    M4   3
514
BUTTON_LEFT   0   0
515
BUTTON_RIGHT  0   0
516
 
517
#                SR  Pin
518
BUTTON_SCRUB     M4   4
519
BUTTON_METRONOME M4   5
520
BUTTON_TAP_TEMPO  0   0
521
BUTTON_JAM_LIVE   0   0
522
BUTTON_JAM_STEP   0   0
523
 
524
#             SR  Pin
525
BUTTON_STOP   M3   5
526
BUTTON_PAUSE  M2   4
527
BUTTON_PLAY   M2   5
528
BUTTON_REW    M3   4
529
BUTTON_FWD    M1   4
530
BUTTON_LOOP    0   0
531
BUTTON_FOLLOW  0   0
532
 
533
#              SR  Pin
534
BUTTON_MENU    M7   5
535
BUTTON_SELECT  M8   4
536
BUTTON_EXIT    M8   5
537
 
538
#              SR  Pin
539
BUTTON_TRACK1  M7   6
540
BUTTON_TRACK2  M7   7
541
BUTTON_TRACK3  M5   6
542
BUTTON_TRACK4  M5   7
543
 
544
#                  SR  Pin
545
BUTTON_PAR_LAYER_A M4   6
546
BUTTON_PAR_LAYER_B M4   7
547
BUTTON_PAR_LAYER_C M3   6
548
 
549
#               SR  Pin
550
BUTTON_EDIT     M5   3
551
BUTTON_MUTE     M6   2
552
BUTTON_PATTERN  M6   3
553
BUTTON_SONG     M7   2
554
 
555
#            SR  Pin
556
BUTTON_SOLO  M6   4
557
BUTTON_FAST  M6   5
558
BUTTON_FAST2  0   0
559
BUTTON_ALL   M7   4
560
 
561
#            SR  Pin
562
BUTTON_GP1   M5   0
563
BUTTON_GP2   M5   1
564
BUTTON_GP3   M6   0
565
BUTTON_GP4   M6   1
566
BUTTON_GP5   M7   0
567
BUTTON_GP6   M7   1
568
BUTTON_GP7   M8   0
569
BUTTON_GP8   M8   1
570
BUTTON_GP9   M4   0
571
BUTTON_GP10  M4   1
572
BUTTON_GP11  M3   0
573
BUTTON_GP12  M3   1
574
BUTTON_GP13  M2   0
575
BUTTON_GP14  M2   1
576
BUTTON_GP15  M1   0
577
BUTTON_GP16  M1   1
578
 
579
#              SR  Pin
580
BUTTON_GROUP1  M8   6
581
BUTTON_GROUP2  M8   7
582
BUTTON_GROUP3  M6   6
583
BUTTON_GROUP4  M6   7
584
 
585
# alternative (individual) track selection buttons
586
# LEDs have to be assigned to TRACKS_DOUT_L_SR and TRACKS_DOUT_R_SR
587
#                     SR  Pin
588
BUTTON_DIRECT_TRACK1   0   0
589
BUTTON_DIRECT_TRACK2   0   0
590
BUTTON_DIRECT_TRACK3   0   0
591
BUTTON_DIRECT_TRACK4   0   0
592
BUTTON_DIRECT_TRACK5   0   0
593
BUTTON_DIRECT_TRACK6   0   0
594
BUTTON_DIRECT_TRACK7   0   0
595
BUTTON_DIRECT_TRACK8   0   0
596
BUTTON_DIRECT_TRACK9   0   0
597
BUTTON_DIRECT_TRACK10  0   0
598
BUTTON_DIRECT_TRACK11  0   0
599
BUTTON_DIRECT_TRACK12  0   0
600
BUTTON_DIRECT_TRACK13  0   0
601
BUTTON_DIRECT_TRACK14  0   0
602
BUTTON_DIRECT_TRACK15  0   0
603
BUTTON_DIRECT_TRACK16  0   0
604
 
605
#                   SR  Pin
606
BUTTON_TRG_LAYER_A  M2   6
607
BUTTON_TRG_LAYER_B  M2   7
608
BUTTON_TRG_LAYER_C  M1   6
609
 
610
 
611
# Following button functions are usually assigned to Fx
612
# buttons, or to dedicated (labeled) buttons
613
# In Wilba's frontpanel layout:
614
# F1 is located at SR M3 Pin 3
615
# F2 is located at SR M2 Pin 2
616
# F3 is located at SR M2 Pin 3
617
# F4 is located at SR M1 Pin 2
618
# and there are dedicated buttons for Copy/Paste/Clear/Utility/StepView
619
 
620
#                    SR  Pin
621
BUTTON_TRACK_SEL     M3   3
622
BUTTON_LIVE          M2   2
623
BUTTON_RECORD        M2   3
624
BUTTON_SAVE_ALL      M1   2
625
 
626
 
627
#                    SR  Pin
628
BUTTON_PAR_LAYER_SEL  0   0
629
BUTTON_TRG_LAYER_SEL  0   0
630
 
631
#               SR  Pin
632
BUTTON_UTILITY  M3   2
633
BUTTON_COPY     M7   3
634
BUTTON_PASTE    M8   2
635
BUTTON_CLEAR    M8   3
636
BUTTON_UNDO      0   0
637
BUTTON_MOVE      0   0
638
BUTTON_SCROLL    0   0
639
BUTTON_BOOKMARK  0   0
640
 
641
#                 SR  Pin
642
BUTTON_STEP_VIEW  M5   5
643
 
644
#                 SR  Pin
645
BUTTON_EXT_RESTART 0   0
646
 
647
#                SR  Pin
648
BUTTON_MIXER      0   0
649
 
650
#                SR  Pin
651
BUTTON_SAVE       0   0
652
 
653
#                   SR  Pin
654
BUTTON_PATTERN_RMX   0   0
655
 
656
#                 SR  Pin
657
BUTTON_FOOTSWITCH  0   0
658
 
659
#                 SR  Pin
660
BUTTON_ENC_BTN_FWD 0   0
661
 
662
#                      SR  Pin
663
BUTTON_TRACK_MODE       0   0
664
BUTTON_TRACK_GROOVE     0   0
665
BUTTON_TRACK_LENGTH     0   0
666
BUTTON_TRACK_DIRECTION  0   0
667
BUTTON_TRACK_MORPH      0   0
668
BUTTON_TRACK_TRANSPOSE  0   0
669
BUTTON_FX               0   0
670
BUTTON_TEMPO_PRESET     0   0
671
 
672
 
673
#                                   SR  Pin
674
BUTTON_MUTE_ALL_TRACKS               0   0
675
BUTTON_MUTE_TRACK_LAYERS             0   0
676
BUTTON_MUTE_ALL_TRACKS_AND_LAYERS    0   0
677
BUTTON_UNMUTE_ALL_TRACKS             0   0
678
BUTTON_UNMUTE_TRACK_LAYERS           0   0
679
BUTTON_UNMUTE_ALL_TRACKS_AND_LAYERS  0   0
680
 
681
 
682
# alternative (individual) bookmark buttons
683
# no LEDs available!
684
#                        SR  Pin
685
BUTTON_DIRECT_BOOKMARK1   0   0
686
BUTTON_DIRECT_BOOKMARK2   0   0
687
BUTTON_DIRECT_BOOKMARK3   0   0
688
BUTTON_DIRECT_BOOKMARK4   0   0
689
BUTTON_DIRECT_BOOKMARK5   0   0
690
BUTTON_DIRECT_BOOKMARK6   0   0
691
BUTTON_DIRECT_BOOKMARK7   0   0
692
BUTTON_DIRECT_BOOKMARK8   0   0
693
BUTTON_DIRECT_BOOKMARK9   0   0
694
BUTTON_DIRECT_BOOKMARK10  0   0
695
BUTTON_DIRECT_BOOKMARK11  0   0
696
BUTTON_DIRECT_BOOKMARK12  0   0
697
BUTTON_DIRECT_BOOKMARK13  0   0
698
BUTTON_DIRECT_BOOKMARK14  0   0
699
BUTTON_DIRECT_BOOKMARK15  0   0
700
BUTTON_DIRECT_BOOKMARK16  0   0
701
 
702
 
703
 
704
##################################################
705
# Button behaviour
706
# 0: active mode as long as button pressed
707
# 1: pressing button toggles the mode
708
##################################################
709
 
710
BUTTON_BEH_FAST         1
711
BUTTON_BEH_FAST2        0
712
BUTTON_BEH_ALL          1
713
BUTTON_BEH_SOLO         1
714
BUTTON_BEH_METRONOME    1
715
BUTTON_BEH_LOOP         1
716
BUTTON_BEH_FOLLOW       1
717
BUTTON_BEH_SCRUB        0
718
BUTTON_BEH_MENU         0
719
BUTTON_BEH_BOOKMARK     1
720
BUTTON_BEH_STEP_VIEW    0
721
BUTTON_BEH_TRG_LAYER    0
722
BUTTON_BEH_PAR_LAYER    0
723
BUTTON_BEH_TRACK_SEL    0
724
BUTTON_BEH_TEMPO_PRESET 0
725
 
726
 
727
##################################################
728
# Special Behaviour of ALL button
729
# 0: only parameter layers are modified by ALL function
730
# 1: trigger and parameter layers are modified by ALL function
731
##################################################
732
BUTTON_BEH_ALL_WITH_TRIGGERS 0
733
 
734
 
735
##################################################
736
# Encoder Functions
737
# SR = 0: encoder disabled
738
# SR = 1..16: DIN assignment
739
# Types: NON_DETENTED, DETENTED1, DETENTED2, DETENTED3, DETENTED4, DETENTED5
740
##################################################
741
 
742
#              SR  Pin  Type
743
ENC_DATAWHEEL   7   7   DETENTED3
744
 
745
# the speed value for the datawheel which is used when the "FAST" button is activated:
746
ENC_DATAWHEEL_FAST_SPEED 3
747
 
748
#        SR  Pin  Type
749
ENC_GP1   1   1   DETENTED3
750
ENC_GP2   1   3   DETENTED3
751
ENC_GP3   1   5   DETENTED3
752
ENC_GP4   1   7   DETENTED3
753
ENC_GP5   3   1   DETENTED3
754
ENC_GP6   3   3   DETENTED3
755
ENC_GP7   3   5   DETENTED3
756
ENC_GP8   3   7   DETENTED3
757
ENC_GP9   4   1   DETENTED3
758
ENC_GP10  4   3   DETENTED3
759
ENC_GP11  4   5   DETENTED3
760
ENC_GP12  4   7   DETENTED3
761
ENC_GP13  6   1   DETENTED3
762
ENC_GP14  6   3   DETENTED3
763
ENC_GP15  6   5   DETENTED3
764
ENC_GP16  6   7   DETENTED3
765
 
766
# the speed value for GP encoders which is used when the "FAST" button is activated:
767
ENC_GP_FAST_SPEED 3
768
 
769
# Auto FAST mode: if a layer is assigned to velocity or CC, the fast button will be automatically
770
# enabled - in other cases (e.g. Note or Length), the fast button will be automatically disabled
771
ENC_AUTO_FAST        1
772
 
773
# optional BPM encoder
774
#              SR  Pin  Type
775
ENC_BPM         0   0   DETENTED3
776
 
777
# the speed value for the BPM encoder which is used when the "FAST" function is activated
778
ENC_BPM_FAST_SPEED 3