Subversion Repositories svn.mios

Rev

Rev 1113 | Rev 1186 | Go to most recent revision | Details | Compare with Previous | Last modification | View Log | RSS feed

Rev Author Line No. Line
163 tk 1
HEADER 3 MBHP DOUT Module
2
 
3
<H1>MIDIbox Hardware Platform, Digital OUT Module</H1>
4
 
1183 tk 5
<P><CENTER><IMG SRC="mbhp/mbhp_dout_r5.jpg" width=500 height=228></CENTER></P>
163 tk 6
 
1183 tk 7
<P CLASS=INFO>The DOUT module comes with multiple serial registers 74HC595; every register provides 8 digital outputs, which are updated with the latch enable signal RCLK and shifted out with the clock signal SCLK. The advantage of using such shift registers is, that they can be cascaded to a long chain without the need of more than 5 cables to the core module. The DOUT board has been designed on a way which allows to cascade not only the ICs on the board, but also several DOUT modules. But note that it depends on the firmware how much outputs are processed by the core module:
8
<UL CLASS=CL>
9
  <LI>MIOS8 based applications typically allow to cascade up to 4 modules (=16 DOUT SRs), makes up to 128 digital outputs
10
  <LI>MIOS32 based applications typically allow to cascade up to 8 modules (=32 DOUT SRs), makes up to 256 digital outputs
11
</UL></P>
163 tk 12
 
1183 tk 13
<P CLASS=DESC>Some applications also allow to scan the shift registers in a so called "matrix" configuration. E.g. a 8x8 matrix (which is driven by a two DOUT SRs) can drive up to 64 LEDs, a 16x16 matrix could drive up to 256 LEDs. But normally 8x8 matrices are perferred due to higher duty cycle: 8x8 matrices make LED visible at 12.5% of the time which is normally bright enough, 16x16 matrices make LED visible at only 6.2% of the time which is mostly too dark!.</P>
14
 
15
<P CLASS=DESC><B>Please note:</B> due to historical reasons, the "first LED" is usually located at D7 of an output connector, while on a <A HREF="mbhp_din.html">MBHP_DIN</A> module the "first button" is located at D0 of an output connector. See also <A HREF="http://www.midibox.org/dokuwiki/doku.php?id=din_dout_pintable" TARGET="_blank">this Wiki page</A>. This might be confusing, on the other hand changing these assignments for newer MIDIbox projects might confuse users even more! Therefore please bear with me that this assignment won't be changed anymore (it also has layout advantages)!</P>
16
 
163 tk 17
<DL>
18
  <DT><H2> <IMG SRC="images/bullet.gif" ALT=""> Download </H2></DT>
19
  <DD>
1113 tk 20
  <P CLASS=DESC><B>Note:</B> To reduce effort only the DOUTX4 variant is available at <A HREF="http://www.mikes-elektronikseite.de" TARGET="_blank">Mikes PCB shop</A> and <A HREF="http://www.midibox-shop.com" TARGET="_blank">SmashTV's MIDIbox Shop</A>. If you don't want to etch the modules by yourself, just use the DOUTX4 and stuff just only the ICs which are really required.</P>
163 tk 21
  <DD><TABLE BORDER=0 CELLSPACING=5 CELLPADDING=0>
22
    <TR>
932 tk 23
      <TD COLSPAN=4 CLASS=TABCOLOR1>PCB data, can be viewed, modified and converted with <A HREF="http://www.cadsoft.de/download.htm" TARGET="_blank">Eagle Light</A>. The .pdf based schematic has been created with <A HREF="http://opencircuitdesign.com/xcircuit" TARGET="_blank">xcircuit</A>. There are no special eagle schematics available, since components have been netlisted in the .brd file directly!</TD>
163 tk 24
    </TR>
25
    <TR>
26
      <TD CLASS=TABCOLOR1><FONT SIZE=2><STRONG>Module</STRONG></FONT></td>
27
      <TD CLASS=TABCOLOR1><FONT SIZE=2><STRONG>Schematic</STRONG></FONT></td>
1183 tk 28
      <TD CLASS=TABCOLOR1><FONT SIZE=2><STRONG>Layout Data (old PCB)</STRONG></FONT></td>
29
      <TD CLASS=TABCOLOR1><FONT SIZE=2><STRONG>Quick-view (old PCB)</STRONG></FONT></TD>
163 tk 30
    </TR>
31
    <TR>
32
      <TD CLASS=TABCOLOR2><I>MBHP_DOUTX4_V1</I></TD>
33
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_doutx4.pdf">mbhp_doutx4.pdf</A></TD>
34
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_doutx4_v1.brd">mbhp_doutx4_v1.brd</A></TD>
35
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_doutx4.gif">mbhp_doutx4.gif</A></TD>
36
    </TR>
37
    <TR>
38
      <TD CLASS=TABCOLOR2><I>MBHP_DOUTX3_V1</I></TD>
878 tk 39
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_doutx3.pdf">mbhp_doutx3.pdf</A></TD>
163 tk 40
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_doutx3_v1.brd">mbhp_doutx3_v1.brd</A></TD>
41
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_doutx3_v1.gif">mbhp_doutx3.gif</A></TD>
42
    </TR>
43
    <TR>
44
      <TD CLASS=TABCOLOR2><I>MBHP_DOUTX2_V1</I></TD>
878 tk 45
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_doutx2.pdf">mbhp_doutx2.pdf</A></TD>
163 tk 46
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_doutx2_v2.brd">mbhp_doutx2_v2.brd</A></TD>
47
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_doutx2_v2.gif">mbhp_doutx2.gif</A></TD>
48
    </TR>
49
    <TR>
878 tk 50
      <TD CLASS=TABCOLOR2><I>MBHP_DOUTX1_V2</I></TD>
51
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_doutx1.pdf">mbhp_doutx1.pdf</A></TD>
52
      <TD CLASS=TABCOLOR2>(normaly built on veroboard)</A></TD>
53
      <TD CLASS=TABCOLOR2>(normaly built on veroboard)</TD>
54
    </TR>
55
    <TR>
163 tk 56
      <TD CLASS=TABCOLOR2><I>MBHP_DOUT_MTC_V1</I></TD>
57
      <TD CLASS=TABCOLOR2>similar to DOUTX4</TD>
58
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_dout_mtc_v1.brd">mbhp_dout_mtc_v1.brd</A></TD>
59
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_dout_mtc_v1.gif">mbhp_dout_mtc.gif</A></TD>
60
    </TR>
1183 tk 61
 
62
    <TR>
63
      <TD CLASS=TABCOLOR1><FONT SIZE=2><STRONG>Module</STRONG></FONT></td>
64
      <TD CLASS=TABCOLOR1><FONT SIZE=2><STRONG>Schematic</STRONG></FONT></td>
65
      <TD CLASS=TABCOLOR1><FONT SIZE=2><STRONG>Layout Data (revised PCB)</STRONG></FONT></td>
66
      <TD CLASS=TABCOLOR1><FONT SIZE=2><STRONG>Quick-view (revised PCB)</STRONG></FONT></TD>
67
    </TR>
68
    <TR>
69
      <TD CLASS=TABCOLOR2><I>MBHP_DOUTX4_R5</I></TD>
70
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_doutx4_r5.pdf">mbhp_doutx4_r5.pdf</A></TD>
71
      <TD CLASS=TABCOLOR2>ask SmashTV</TD>
72
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_dout_r5_detail.jpg">mbhp_dout_r5_detail.jpg</A></TD>
73
    </TR>
163 tk 74
  </TABLE></DD>
75
 
76
  <DD><TABLE BORDER=0 CELLSPACING=5 CELLPADDING=0>
77
    <TR>
78
      <TD COLSPAN=4 CLASS=TABCOLOR1><FONT SIZE=3>Additional informations</FONT></TD>
79
    </TR>
80
    <TR>
81
      <TD CLASS=TABCOLOR1><FONT SIZE=2><STRONG>File</STRONG></FONT></td>
82
      <TD CLASS=TABCOLOR1><FONT SIZE=2><STRONG>Size</STRONG></FONT></td>
83
      <TD NOWRAP CLASS=TABCOLOR1><FONT SIZE=2><STRONG>Description</STRONG></FONT></TD>
84
    </TR>
85
    <TR>
86
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_doutx4_orderlist.txt">mbhp_doutx4_orderlist.txt</A></TD>
87
      <TD CLASS=TABCOLOR2>1k</TD>
1183 tk 88
      <TD CLASS=TABCOLOR2><A HREF="http://www.reichelt.de/" TARGET="_blank">Reichelt</A> orderlist for old layout</TD>
163 tk 89
    </TR>
90
    <TR>
1183 tk 91
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_doutx4_r5_orderlist.txt">mbhp_doutx4_r5_orderlist.txt</A></TD>
92
      <TD CLASS=TABCOLOR2>1k</TD>
93
      <TD CLASS=TABCOLOR2><A HREF="http://www.reichelt.de/" TARGET="_blank">Reichelt</A> orderlist for SmashTV layout</TD>
94
    </TR>
95
    <TR>
163 tk 96
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_doutx4_32leds.pdf">mbhp_doutx4_32leds.pdf</A></TD>
97
      <TD CLASS=TABCOLOR2>16k</TD>
1183 tk 98
      <TD CLASS=TABCOLOR2>How to connect 32 LEDs (old PCB)</TD>
163 tk 99
    </TR>
100
    <TR>
101
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_doutx4_ledrings.pdf">mbhp_doutx4_ledrings.pdf</A></TD>
102
      <TD CLASS=TABCOLOR2>31k</TD>
1183 tk 103
      <TD CLASS=TABCOLOR2>How to connect 16 LED-rings (old PCB)</TD>
163 tk 104
    </TR>
105
    <TR>
106
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_doutx4_mtc.pdf">mbhp_doutx4_mtc.pdf</A></TD>
107
      <TD CLASS=TABCOLOR2>12k</TD>
1183 tk 108
      <TD CLASS=TABCOLOR2>How to connect 8 LED-digits for the MTC display of <A HREF="midimon.html">MIDImon</A> (old PCB)</TD>
163 tk 109
    </TR>
110
    <TR>
111
      <TD CLASS=TABCOLOR2><A HREF="mbhp/mbhp_doutx1_reed_relays.pdf">mbhp_doutx1_reed_relays.pdf</A></TD>
112
      <TD CLASS=TABCOLOR2>9k</TD>
1183 tk 113
      <TD CLASS=TABCOLOR2>How to connect Reed Relays to a DOUT module (old PCB) - see also <A HREF="mbhp/mbhp_doutx1_reed_relays.jpg">this photo</A></TD>
163 tk 114
    </TR>
115
  </TABLE></DD>
116
  </DD>
117
</DL>
118
 
119
<DL>
120
   <DT><H2> <IMG SRC="images/bullet.gif" ALT=""> Available Ports </H2></DT>
121
   <DD>
1183 tk 122
<P CLASS=DESC>Following interfaces are provided by the DOUTX4 module:</P>
163 tk 123
  <DD><TABLE CLASS=BOX WIDTH="100%" BORDER=1 CELLSPACING=5 CELLPADDING=0>
124
 
125
    <TR>
126
      <TD CLASS=TABCOLOR1><FONT SIZE=2><STRONG>Name</STRONG></FONT></td>
127
      <TD CLASS=TABCOLOR1><FONT SIZE=2><STRONG>No. of pins</STRONG></FONT></td>
128
      <TD NOWRAP CLASS=TABCOLOR1><FONT SIZE=2><STRONG>Description</STRONG></FONT></TD>
129
    </TR>
130
    <TR>
131
      <TD CLASS=TABCOLOR2>J1</TD>
132
      <TD CLASS=TABCOLOR2>5</TD>
1183 tk 133
      <TD CLASS=TABCOLOR2>Interface to CORE:J8 (if LEDs are used). DOUTX4:J1 provides two power pins for 5V/0V, the serial clock, the latch enable and the serial input of the register chain.<BR>This port can also be connected with J2 of another DOUTX module.<BR>
134
      The revised PCB layout from SmashTV uses a 2-row DIL Header instead to simplify the connection to the J8/9 connector of the core module.</TD>
163 tk 135
    </TR>
136
 
137
    <TR>
138
      <TD CLASS=TABCOLOR2>J2</TD>
139
      <TD CLASS=TABCOLOR2>5</TD>
1183 tk 140
      <TD CLASS=TABCOLOR2>Interface to another DOUTX4 module. DOUTX4:J2 provides nearly the same pins like J1, just only the serial input of the first IC is replaced by the serial output of the last IC.<BR>This port can be connected with J1 of the next DOUTX module.</TD>
163 tk 141
    </TR>
142
 
143
    <TR>
144
      <TD CLASS=TABCOLOR2>J3-J6</TD>
145
      <TD CLASS=TABCOLOR2>5</TD>
1183 tk 146
      <TD CLASS=TABCOLOR2>These are the digital output lines, every connector comes with 8 of them and an additional pin for ground. See <A HREF="mbhp/mbhp_doutx4_32leds.pdf">mbhp_doutx4_32leds.pdf</A> as an example how to connect LEDs to these pins, and <A HREF="mbhp/mbhp_doutx4_ledrings.pdf">mbhp_doutx4_ledrings.pdf</A> how to connect LED rings.<BR>
147
</TD>
148
      The revised PCB layout from SmashTV uses 2-row DIL headers instead so that buttons can be easily connected via 2-row DIL sockets.</TD>
163 tk 149
    </TR>
150
  </TABLE></DD>
151
  </DD>
152
</DL>
153
 
154
 
155
<DL>
156
   <DT><H2> <IMG SRC="images/bullet.gif" ALT=""> Used Components </H2></DT>
157
   <DD>
1183 tk 158
   <DD><TABLE CLASS=BOX WIDTH="100%" BORDER=1 CELLSPACING=5 CELLPADDING=0>
163 tk 159
 
160
    <TR>
161
      <TD CLASS=TABCOLOR1><FONT SIZE=2><STRONG>Part Name</STRONG></FONT></td>
162
      <TD CLASS=TABCOLOR1><FONT SIZE=2><STRONG>Value</STRONG></FONT></td>
163
      <TD NOWRAP CLASS=TABCOLOR1><FONT SIZE=2><STRONG>Description</STRONG></FONT></TD>
164
    </TR>
165
 
166
    <TR>
167
      <TD CLASS=TABCOLOR2>IC1, IC2, IC3, IC4</TD>
168
      <TD CLASS=TABCOLOR2>74HC595</TD>
169
      <TD CLASS=TABCOLOR2>The digital output shift registers</TD>
170
    </TR>
171
 
172
    <TR>
173
      <TD CLASS=TABCOLOR2>R1-R32</TD>
174
      <TD CLASS=TABCOLOR2>220</TD>
175
      <TD CLASS=TABCOLOR2>These resistors are required if LEDs should be driven with the output, just to limit the current through the LEDs. If you are using the DOUT module with a MIDIO128, and would like to drive additional logic chips instead of LEDs, these resistors are not required and can be replaced by bridges.<BR>If the module is used to drive the LED-Rings of MIDIbox16E, R1-R16 have to be replaced by bridges, see also <A HREF="mbhp/mbhp_doutx4_ledrings.pdf">mbhp_doutx4_ledrings.pdf</A></B></TD>
176
    </TR>
177
 
178
    <TR>
179
      <TD CLASS=TABCOLOR2>C1-C4</TD>
180
      <TD CLASS=TABCOLOR2>100nF</TD>
181
      <TD CLASS=TABCOLOR2>The additional bypass caps have to be placed on the bottom side of the PCB, as close to the +5V power input of the 74HC595 as possible.</TD>
182
    </TR>
183
 
184
    <TR>
185
      <TD CLASS=TABCOLOR2>J*</TD>
186
      <TD CLASS=TABCOLOR2>*</TD>
187
      <TD CLASS=TABCOLOR2>All connectors are optional, the cables can also be soldered directly into the board. Otherwise I suggest SIL headers (header sockets), known from PC motherboards. They are cheap and usefull.</TD>
188
    </TR>
189
 
190
    <TR>
191
      <TD CLASS=TABCOLOR2>DIL</TD>
192
      <TD CLASS=TABCOLOR2>SOCKETS</TD>
1183 tk 193
      <TD CLASS=TABCOLOR2>Don't forget to buy sockets for the shift registers. 4 * 16 pin DIL sockets are required for the old PCB layout, resp. 4 2x5 DIL sockets for the SmashTV layout.</TD>
163 tk 194
    </TR>
195
  </TABLE></DD>
196
  </DD>
197
</DL>
198
 
199
 
200
<DL>
201
  <DT><H2> <IMG SRC="images/bullet.gif" ALT=""> Soldering Guide </H2></DT>
202
  <DD>
1183 tk 203
  <P CLASS=DESC>This soldering guide explains how to build a DOUT module based on the revised layout from <A HREF="http://www.midibox-shop.com" TARGET="_blank">SmashTV</A>. If you want to build a DOUT module based on the old layout (e.g. from <A HREF="http://www.mikes-elektronikseite.de" TARGET="_blank">Mike</A>) please continue at <A HREF="mbhp_dout_oldpcb.html">this page</A>.</P>
204
 
163 tk 205
  <DD><TABLE CELLSPACING=0 CELLPADDING=0>
206
    <TR>
1183 tk 207
      <TD><IMG SRC="mbhp/mbhp_dout_r5_2.jpg" WIDTH=280 HEIGHT=139 BORDER=0 ALT=""></TD>
208
      <TD CLASS=TABCOLOR2>It's always a good idea to start with the smallest components to simplify mounting.<BR>
209
So, start with the caps:
210
<UL>
211
<LI>C1-C4: 100 nF
212
</UL>
163 tk 213
    </TR>
214
    <TR>
1183 tk 215
      <TD><IMG SRC="mbhp/mbhp_dout_r5_3.jpg" WIDTH=280 HEIGHT=143 BORDER=0 ALT=""></TD>
216
      <TD CLASS=TABCOLOR2>Continue with the 4 IC sockets.</TD>
163 tk 217
    </TR>
218
    <TR>
1183 tk 219
      <TD><IMG SRC="mbhp/mbhp_dout_r5_4.jpg" WIDTH=280 HEIGHT=142 BORDER=0 ALT=""></TD>
220
      <TD CLASS=TABCOLOR2>And then solder the resistors - here I'm using the nice 8x220 Ohm arrays (which look like ICs). Unfortunately they are only available at <A HREF="http://www.mouser.com" TARGET="_blank">Mouser</A> (652-4116R-1LF-220). Alternatively mount 32 discrete 220 Ohm resistors (not shown here).</TD>
163 tk 221
    </TR>
222
    <TR>
1183 tk 223
      <TD><IMG SRC="mbhp/mbhp_dout_r5_5.jpg" WIDTH=280 HEIGHT=132 BORDER=0 ALT=""></TD>
224
      <TD CLASS=TABCOLOR2>Thereafter mount the 2x5 SIL headers. As you can see, we are using "polarized" headers for J1 and J2, and DIL headers for J3-J6, so that the silkscreen (which shows the pin names) won't be hidden. It's your personal choice to use "polarized" headers for these connections as well.</TD>
163 tk 225
    </TR>
226
    <TR>
1183 tk 227
      <TD><IMG SRC="mbhp/mbhp_dout_r5_6.jpg" WIDTH=280 HEIGHT=129 BORDER=0 ALT=""></TD>
228
      <TD CLASS=TABCOLOR2>Finally put the 74HC595 ICs into the sockets. Your module is now ready for use!</TD>
163 tk 229
    </TR>
230
    <TR>
1183 tk 231
      <TD COLSPAN=2 CLASS=TABCOLOR2><IMG SRC="mbhp/mbhp_dout_r5_chain.jpg" WIDTH=500 HEIGHT=290 BORDER=0 ALT=""><BR>
232
      Two cascaded DOUTX4 modules connected to J8/9 of a <A HREF="mbhp_core_stm32f4.html">MBHP_CORE_STM32F4</A> module with selfmade IDC cables.</TD>
163 tk 233
    </TR>
234
    <TR>
1183 tk 235
      <TD COLSPAN=2 CLASS=TABCOLOR2><IMG SRC="mbhp/mbhp_dindout_r5_chain.jpg" WIDTH=500 HEIGHT=268 BORDER=0 ALT=""><BR>
236
      Two cascaded <A HREF="mbhp_din.html">DINX4</A> and two DOUTX4 modules connected to J8/9 of a <A HREF="mbhp_core_stm32f4.html">MBHP_CORE_STM32F4</A> module with selfmade IDC cables.<BR>
237
      <A HREF="mbhp/mbhp_dindout_cable.jpg">This picture</A> gives you a more detailed view of the special (selfmade) cable which has one additional DIL socket at the middle so that the DIN and DOUT chain can be connected to the J8/9 connector of the core module.</TD>
163 tk 238
    </TR>
239
  </TABLE></DD>
240
  </DD>
241
</DL>
242
 
243
FOOTER